NHTSA ID Number: 10137256
Manufacturer Communication Number: PI1314A
Summary
This preliminary informational bulletin provides repair information to correct a customer concern of a front body creak/pop type noise (located in the front passenger foot well area) noticed when turning the steering wheel when the vehicle is stationary or during slow speed maneuvers.
4 Affected Products
Vehicles
Parts Information
| Rivet | 2 | 11519023
No products found. |
| Crest “Black Majik” Adhesive Kit | 1 | CB-M1 |
| Crest “Jet Black” Adhesive Kit | 1 | CE-JB |
SEOCONTENT-START
| Subject: | Creak/Pop Type Noise from Right Front of Vehicle During Low Speed Maneuvers |
| Models: | 2014-2015 Chevrolet Equinox |
| 2014-2015 GMC Terrain | |
| All Built Prior to August 5, 2014 | |
| Attention: | This PI also applies to any of the above models that may be Export vehicles. |
Condition/Concern
Some customers may comment on a front body creak/pop type noise when turning the steering wheel when the vehicle is stationary or during slow speed maneuvers. This noise is located in the front passenger foot well area.
This condition may be caused by an insufficiently tightened cradle mount bolt or two out of position spot welds within the front right frame rail.
Recommendation/Instructions
Use the following steps to diagnose and correct the condition:
- Road test the vehicle to verify the condition.
- Raise the vehicle. Refer to Lifting and Jacking the Vehicle in SI.
- Check the front suspension crossmember to body mounting bolts. if the torque is less than the published 155 Nm (114 lb ft) specifications, replace the body mounting bolts with NEW bolts before obtaining to prescribed torque.
- Road test the vehicle and determine if the condition is corrected.
- If the condition is corrected, the repair is complete.
- If the noise is still present, continue to the next step.
- Remove the right front seat. It is not necessary to completely remove the seat from the vehicle. Fold the right rear seat down and place the seat assembly on the cargo floor. Refer to Driver or Passenger Seat Removal and Installation in SI.
- Remove the right side console trim plate. Refer to Front Floor Console Trim Plate Replacement in SI.
- Remove the right front hinge pillar trim. Refer to Body Hinge Pillar Trim Panel Replacement in SI.
- Fold back the right front carpet but do not remove the carpet from the vehicle.
- Remove the HVAC blower motor. Refer to Blower Motor Replacement in SI.
- Remove the body plug. Save the plug as it will be reused.
- Using a gasket scraper, remove the sound deadener material from the repair area as shown.
- Measure up from the body hole 90 mm (3.5 in) (1). Create a cross car line (2).
- Measure up from that line an additional 50 mm (2.0 in) (1). Create a second cross car line (2).
- From the center mark, measure 45 mm (1.75 in) in both directions (1). Create two lines connecting the cross car lines.
- Using a cut off wheel, cut along both cross car lines and the inboard connecting line.
- Bend the tab back revealing the two spot welds as shown.
- Create two drill locations 6 mm (0.25 in) down from the edge of the metal.
- Locate the inboard mark slightly to the left of the spot weld.
- Locate the outboard mark above the spot weld.
- Center punch the drill locations.
- Drill two 0.25 in holes.
- Prepare a small quantity of *Crest Industries CB-M1 “Black Majik” 10 minute adhesive. Follow the manufacturers instructions for prepping cartridge and dispensing adhesive.
- Coat the two #11519023 rivets as shown.
- Prepare a quantity of Crest Industries CE-JB “Jet Black” 1.5 minute adhesive. Follow the manufacturers instructions for prepping cartridge and dispensing adhesive. Coat the edges of the metal tab and opening.
- Bend the tab back into position and add additional CE-JB “Jet Black” adhesive to the joint. Hold in position while the material cures.
- Reinstall and seal the body plug.
- Prepare a quantity of Crest Industries CB-M1 “Black Majik” adhesive and apply to the complete area. Using a plastic spreader, coat the complete area.
- Prepare 3 150 mm (6.0 in) long strips of fiberglass mesh tape.
- Install the tape cross car in the vehicle overlapping the complete area. Use a small brush to saturate the tape with adhesive.
- Apply an additional coat of Crest Industries CB-M1 “Black Majik” adhesive. Use a plastic spreader to smooth the repair area.
- Reinstall the HVAC blower motor. Refer to Blower Motor Replacement in SI.
- Reinstall the carpet, right side console trim plate, right hinge pillar trim and the seat. Refer to the appropriate SI procedures listed above.
*We believe these sources and their products to be reliable. There may be additional manufacturers of such material. General Motors does not endorse, indicate any preference for or assume any responsibility for the products from these firms or for any such items which may be available from other sources
Parts Information
The adhesive material, fiberglass mesh tape and brushes can be ordered directly from Crest Industries Inc. at 1 (800) 822-4100. Canadian Dealers: Call J-2 Products (Crest Distributor) at 1-888-880-0025 or 416-665-1404, 8:00 am – 5:00 pm ET.
| Part Number | Description | Material Allowance |
| 11519023
No products found. |
Rivet | 2 |
| *CB-M1 | Crest “Black Majik” Adhesive Kit | 1 |
| *CE-JB | Crest “Jet Black” Adhesive Kit | 1 |
Warranty Information
For vehicles repaired under warranty, use:
| Labor Operation | Description | Labor Time |
| 1480368* | Install Two Structural Rivets To Frame Rail | 1.7 hrs |
| *This is a unique Labor Operation for Bulletin use only. It will not be published in the Labor Time Guide. | ||
SEOCONTENT-END
Bulletin No.: PI1314A
Date: Nov-2015
To View or Download this Document Click Here
Bulletin No.: PI1314
Date: September, 2014
To View or Download this Document Click Here
Bulletin No.: PI1314
Date: September, 2014
To View or Download this Document Click Here
Bulletin No.: PI1314
Date: September, 2014
To View or Download this Document Click Here
SaleBestseller No. 1
INCLY 1000PCS Aluminum Pop Rivets Assortment Kit with Washers
- 【1000pcs Pop Rivets Set】: This pop rivets assortment kit with washers set includes 14 most used sizes for your various needs. Among, including 50pcs 3/32” x 1/4”, 50pcs 3/32” x 5/16”, 35pcs 1/8” x 1/4”, 40pcs 1/8” x 5/16”, 50pcs 1/8” x 3/8”, 50pcs 1/8” x 1/2”, 45pcs 5/32” x 3/8”, 35pcs 5/32” x 1/2”, 30pcs 3/16” x 5/16”, 30pcs 3/16” x 3/8”, 30pcs 3/16” x 1/2”, 30pcs 3/16” x 5/8”, 15pcs 1/4” x 3/8”, 10pcs 1/4” x 1/2”, total 500 pcs pop rivets. It also comes with 500pcs 5 sizes pop rivets washers.
- 【Enhanced Stability with Washers】: Designed specifically for pop rivets, this rivet backup washers provide extra support for fastening rivets when facing oversized holes. Among, including 100pcs 3/32” , 175pcs 1/8” , 80pcs 5/32”, 120pcs 3/16” , 25pcs 1/4” , total 500pcs pop rivets washers. This combination prevents rivet pull-out and significantly boosts overall stability during installation.
- 【High Quality Material】: These aluminum rivets & washers are made of high-quality aluminum & steel, and 304 stainless steel, which has excellent corrosion resistance, high hardness, anti-rust and anti-oxidation properties in harsh environments, ensuring the blind rivets & washers have a great performance and a long service life.
- 【Convenient Storage】: The aluminum pop rivets kit comes in reinforced storage with modular compartment design and well-designed label, easily identify different size of pop rivets and pop rivet washers, and effectively organizing the rivets for metal. Easy to install, store and carry out, preventing from messy or loss.
- 【Widely Used】: INCLY aluminum pop rivets with washers are suitable for indoor & outdoor use, such as DIY home uses, business, automotive repair, aviation, pipework, laminates,instruments, furniture, boat and so on for various needs.
Bestseller No. 2
ZQZ 162 Pcs 3/16 Inches Black Pop Rivets Assortment Kit - 4 Sizes Black Aluminum Rivets 3/16" x (5/16", 3/8", 1/2", 5/8"), Black Blind Rivets for Metal, Dome Head rivet kit
- Product Specifications: 3/16” black pop rivets assortment kit including 49pcs 3/16” x 5/16”, 49pcs 3/16” x 3/8”, 34pcs 3/16” x 1/2”, 30pcs 3/16” x 5/8”, for a total of 162 pcs
- High-Quality Materials: Our 3/16” black rivets are made of high-quality aluminum and steel, which gives them high strength, durability and corrosion resistance, ensuring these blind rivets have a great performance and a long service life
- Convenient Storage: All 3/16” aluminum rivets are stored in a portable transparent case. Rivets of different sizes are kept separately in plastic bags, designed for easy access and use, ensuring rivets won't get lost or mixed up during operation
- Easy Installation: Our blind rivets have a smooth surface, are strong and handy, allow for single-sided installation, making them ideal for tight spaces and hard-to-reach areas. Made from aluminum and steel material, you don't need to worry about them rusting and breaking. These pop rivets are durable with no deformation
- Wide Application: Our aluminum pop rivets are perfect for metal, automotive, and various DIY projects requiring sturdy and secure fastening to ensure a secure and stable connection. You can use these blind rivets indoors and outdoors
Bestseller No. 3
ZQZ 140 Pcs 3/16 Inches Pop Rivets Assortment Kit - 4 Sizes Aluminum Rivets 3/16" x (5/16", 3/8", 1/2", 5/8"), Blind Rivets for Metal, Dome Head rivet kit
- Product Specifications: 3/16” pop rivets assortment kit including 43pcs 3/16” x 5/16”, 43pcs 3/16” x 3/8”, 29pcs 3/16” x 1/2”, 25pcs 3/16” x 5/8”, for a total of 140 pcs
- High-Quality Materials: Our 3/16” rivets are made of high-quality aluminum and steel, which gives them high strength, durability and corrosion resistance, ensuring these blind rivets have a great performance and a long service life
- Convenient Storage: All 3/16” aluminum rivets are stored in a portable transparent case. Rivets of different sizes are kept separately in plastic bags, designed for easy access and use, ensuring rivets won't get lost or mixed up during operation
- Easy Installation: Our blind rivets have a smooth surface, are strong and handy, allow for single-sided installation, making them ideal for tight spaces and hard-to-reach areas. Made from aluminum and steel material, you don't need to worry about them rusting and breaking. These pop rivets are durable with no deformation
- Wide Application: Our aluminum pop rivets are perfect for metal, automotive, and various DIY projects requiring sturdy and secure fastening to ensure a secure and stable connection. You can use these blind rivets indoors and outdoors
Bestseller No. 4
900 Pcs Black Pop Rivet Kit, 3/32", 1/8", 5/32", 3/16"
- Superb Materials: The black pop rivets' body is made of aluminum, which is rust-resistant, corrosion-resistant, break-resistant, and deform-resistant. It is also strong, durable, and stable.
- Washers Design: The washer design ensures high tightening force, effectively preventing loosening and significantly improving fastening performance and functionality.
- Easy to Use: Black blind rivets are perfectly compatible with rivet guns and can be quickly installed using rivet tools (manual, electric, or pneumatic), can be used to easily connect metal sheets, wood panels, plastic panels, and other components.
- Wide Applications: Suitable for industrial and construction applications, such as machinery, ships, automobiles, appliances, furniture, aviation, piping systems, ships, railway tracks, furniture, or DIY.
- Package includes: 535 pieces of aluminum rivets in 14 sizes, with 365 pieces of washers, which can be used for multiple uses on site and daily needs. All metal rivets are stored in a storage box so that you can quickly identify the required size and improve work efficiency.
Bestseller No. 5
ASKWAY Pressure Rivet Nut Tool Kit, 430Pcs Aluminum Rivet Nut Combination
- Dear Customer, we have recently received feedback from some users regarding issues with thread stripping during installation. To prevent any disruption to your work and to save your valuable time, we would like to inform you that this rivet nut is manufactured from 6061 aluminum. Rivet nuts made from 6061 aluminum are characterized by their soft and lightweight nature, making them extremely easy to rivet; you need only apply very slight pressure to complete the riveting process. Applying excessive pressure, however, will result in the threads stripping.
- Although rivet nuts made from 6061 aluminum alloy possess lower tensile strength than those made of carbon steel or stainless steel, they offer distinct advantages, such as ease of riveting and installation, as well as excellent rust and corrosion resistance. If you require high-strength rivet nuts, we recommend choosing those made from carbon steel or stainless steel. Our ASKWAY store on Amazon offers comprehensive rivet nut tool kits available in carbon steel, stainless steel, and aluminum options. Selecting the appropriate rivet nut material for your specific needs is of paramount importance.
- [About this project]: This rivet nut tool kit includes 1pc set rivet nut installer, which provides 5 metric thread sizes of embedded rivet nuts, including: 160pcsM3×0.5, 110pcsM4×0.7, 70pcsM5×0.8, 70pcsM6×1.0, 20pcsM8×1.25, a total of 430pcs of rivet nuts, which can meet your various daily needs.
- 【Wide Application】: Rivet nuts are commonly used fastener products in our tool room. When you need it, it will bring you a lot of convenience. Embedded rivet nuts provide a firm connection for screws and bolts in your home decoration and industrial applications. They are widely used in home appliances, car repairs, furniture, metal doors and windows, home decoration, sheet metal assembly and industrial applications.
- [After-sales Service]: Our team focuses on the research and development, production and sales of fasteners. We are confident in the quality of our rivet embedded nuts and provide long-term service. If you encounter any problems during use, please contact online customer service and our team will provide you with a solution as soon as possible.
This product presentation was made with AAWP plugin.
We have this exact same problem on a 2014 Buick Enclave but can’t find a bulletin like this for our vehicle. Have others with a Traverse, Enclave, or Acadia reported this issue?