“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10118253
Manufacturer Communication Number: PIT5501F
Summary
This Preliminary Information communication provides information to the technician on the steps to diagnosis and repair steering that feels loose or has excessive play. This concern could be caused by the Pitman Shaft Over-Center Preload Adjustment becoming misadjusted. Technician will need to replace the steering gear pitman arm shaft with an updated design.
2 Affected Products
Vehicles
MAKE | MODEL | YEAR |
CHEVROLET | SILVERADO 2500 | 2016 |
GMC | SIERRA 2500 | 2016 |
SEOCONTENT-START
Bulletin No.: PIT5501F
Published date: 06/8/2017
Preliminary Information
PIT5501F Steering Feels Loose / Excessive Lash / Fluid Leak At Lash Adjuster
Product Investigation Review Required
Models
Brand: | Model: | Model Years: | VIN: | Engine: | Transmissions: | |
---|---|---|---|---|---|---|
from | to | |||||
Chevrolet | Silverado 2500/3500 | 2016 | All | All | All | All |
GMC | Sierra 2500/3500 | 2016 | All | All | All | All |
Supersession Statement
This PI was superseded to remove the 2017 model year. Please discard PIT5501E.
The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.
Condition / Concern
Some owners may comment of the following:
- The steering feels loose
- There is excessive play in the steering
- A small power steering fluid leak from the steering gear lash adjuster stud/nut area
These concerns could be caused by the pitman shaft adjuster stud (3) unthreading up/out of the cover plate, which can cause excessive lash in the steering gear. This issue is NOT caused by the lock nut (4) turning on the adjuster stud (3), shown below.
Inspect the pitman shaft adjuster stud for being loose. This will be obvious after inspecting the pitman shaft adjuster stud/nut as follows:
- The adjuster stud nut (4) will not be seated up against the cover plate, shown below.
- The adjuster stud (3) can easily be turned in or out by hand using an Allen wrench.
If it is found that the pitman shaft adjuster stud (3) has unthreaded up/out AND there is NO reason to believe someone has previously turned the adjuster stud nut (4) on the adjuster stud (3), continue to the recommendations section to apply thread locker on the adjuster stud threads.
If the adjuster stud has NOT unthreaded up/out of the cover plate, but it is suspected the issue is caused by excessive lash in the steering gear, the following test can be performed to determine if there is excessive lash in the steering gear:
- Disconnect the Relay Rod/Center link from the steering gear pitman arm and idler arm. Allow the relay rod/center link to drop down and clear the pitman arm.
- With the steering gear in the centered position (wheels straight forward), have an assistant hold the steering wheel from turning.
- While the steering wheel is being held in the centered position, wiggle the pitman arm and feel for any lash/play.
If any lash/play is found, OR there IS reason to believe someone has turned the adjuster stud nut (4) on the adjuster stud (3), follow the SI procedure titled “Steering Gear Pitman Shaft Over-Center Preload Adjustment – Off Vehicle (Heavy Duty)”.
Recommendations / Instructions
Do NOT REMOVE the steering gear from the vehicle.
To correct this concern, use the following procedure to apply blue thread locker GM P/N 19333511 (Canada 10953489) to the adjuster stud threads, which will secure it to the cover plate:
- Position the steering wheel in the centered position so the wheels are pointed straight ahead. Following SI, remove the left front wheel, left front wheelhouse liner, and charge air cooler inlet pipe (if equipped), as shown below.
- Using a marker or scribe, mark the adjuster stud in relation to the adjuster stud nut, as shown below (1). This is just in case the nut is turned on the adjuster stud when performing the following repairs.
- Using an Allen wrench, loosen the adjuster stud (turning it counter clockwise) until it is fully backed off, typically 2 threads will be shown (2). Note: Do NOT turn the nut relative to the adjuster stud.
- Using brake cleaner, spray the threads to remove any oil residue. Then, blow the remaining brake cleaner off with compressed air.
- Apply a thick layer of blue thread locker GM P/N 19333511 (Canada 10953489) around the adjuster stud threads, shown below.
- Using an Allen wrench, tighten the adjuster stud (turning clockwise) until the nut bottoms out on the cover plate, shown below.
Note: DO NOT hold the nut. Doing so could cause the adjuster stud to seat at the incorrect depth, therefore changing the lash adjustment.
- Using a torque wrench with crow foot & Allen wrench, turn the adjuster stud and nut simultaneously while torquing to 68 lb ft (92 Nm). Make sure the mark or scribe on the adjuster stud and nut (made during step 2) are still in alignment. If not, slightly loosen the nut, realign the marks, and retorque.
- Following SI, reinstall the charge air cooler inlet pipe (if equipped), the left front wheelhouse liner, and left front wheel.
Note: Ensure the charge air cooler inlet pipe is fully installed and the clamp is fully torqued.
- Before test driving, allow the thread locker (Loctite) to dry for at least 4 hours. The vehicle can be removed from the hoist to a holding position.
Trucks with OUT Active Hydraulic Assist system (RPO NV8) test drive to verify customer complaint is corrected.
Trucks with the Active Hydraulic Assist system (RPO NV8) continue with the following steps.
- Reprogram the Power Steering Control module with the latest calibrations in Tis2Web.
- Using the scan tool perform a Steering Angle Sensor Centering procedure listed in SI (example doc id 3970641).
- Next, with the ignition ON, engine OFF, steering wheel straight forward and NO steering wheel input, use the scan tool and go into the Power Steering Control Module/ Configuration and Reset Functions and perform a “Power Steering Pressure Sensor Learn”.
- Test drive the truck and make sure the steering wheel is level and the “Steering Wheel Angle” parameter is 0 degrees (+/-3 degrees) while driving the truck on a flat level straight road at slower speeds (approximately 25 mph). To view the “Steering Wheel Angle” parameter, using the scan tool and go into the Power Steering Control Module/Data Display.
- Complete test drive to verify customer complaint is corrected.
If customer compliant is not corrected, perform SI “Steering Gear Pitman Shaft Replacement – DOC ID 4165698.”
Warranty Information
For vehicles repaired under warranty, use:
Labor Operation | Description | Labor Time |
7480288* | Clean threads, apply thread lock and torque pitman shaft stud adjuster | 1.2 hr. |
Add ONLY WITH RPO NV8 | Perform GDS2 SAS and Pressure Sensor Relearns | 0.3 hr. |
Add ONLY WITH RPO NV8 | If Necessary Reprogram the Power Steering Control Module | 0.3 hr. |
* This is a unique labor operation for bulletin use only. This will not be published in the Labor Time Guide. |
Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.
SEOCONTENT-END
Bulletin No.: PIT5501F
Published date: 06/8/2017
https://www.nhtsa.gov/recalls?nhtsaId=10118253
https://static.nhtsa.gov/odi/tsbs/2017/MC-10118253-9999.pdf
To View or Download this Document Click Here
Bulletin No.: PIT5501E
Published date: 03/7/2017
https://www.nhtsa.gov/recalls?nhtsaId=10116654
https://static.nhtsa.gov/odi/tsbs/2017/MC-10116654-9999.pdf
To View or Download this Document Click Here
Bulletin No.: PIT5501D
Date: Nov-2016
https://www.nhtsa.gov/recalls?nhtsaId=10114834
https://static.nhtsa.gov/odi/tsbs/2016/MC-10114834-9999.pdf
To View or Download this Document Click Here
Bulletin No.: PIT5501B
Date: Jun-2016
https://www.nhtsa.gov/recalls?nhtsaId=10081240
https://static.nhtsa.gov/odi/tsbs/2016/SB-10081240-2280.pdf
To View or Download this Document Click Here
Bulletin No.: PIT5501A
Date: Apr-2016
https://www.nhtsa.gov/recalls?nhtsaId=10083856
https://static.nhtsa.gov/odi/tsbs/2016/SB-10083856-5448.pdf
To View or Download this Document Click Here
https://www.nhtsa.gov/recalls?nhtsaId=10078740
https://static.nhtsa.gov/odi/tsbs/2016/SB-10078740-7690.pdf
To View or Download this Document Click Here
Bulletin No.: PIT5501
Date: Mar-2016
https://www.nhtsa.gov/recalls?nhtsaId=10113940
https://static.nhtsa.gov/odi/tsbs/2016/MC-10113940-9999.pdf
To View or Download this Document Click Here
Reprogramming
GM Diagnostic/Programming (TIS2Web)
Approved J2534 Device with TIS2WEB can reprogram 1996 and later All GM Modules.
To obtain the latest electronic controller calibration information for your vehicle, go to https://tis2web.service.gm.com/tis2web and enter the vehicle's 17 character Vehicle Identification Number (VIN) and select 'Get CAL ID’.
You can then compare the latest part number with the actual number installed on the vehicle to determine if a reprogram is needed.
The Service Programming System (SPS) application is part of the TIS2Web system. To program an ECU, the SPS application must communicate with the vehicle control modules using the proper J2534 programming interface tool.
The following are the supported interface tools:
The Tech 2 supports model years 1996 and beyond. With the addition of the CAN Diagnostic Interface (CANdi) module, Tech 2 is fully backward compatible with current Tech 2 functionality and operates transparently when diagnosing non-CAN-equipped vehicles.
Servicing the next generation Global A vehicles will require the diagnostic software, GDS2, Global Diagnostic System 2 running on a local PC device while the MDI is connected to the vehicle. The GM MDI is the Global Diagnostic tool for future vehicles starting with Global A vehicles.
The GM MDI was introduced in the fall of 2007 for Pass-Thru programming and offers faster programming speed. It can be used to perform Pass-Thru programming on all vehicles built since 1996 and into the future. Click here to view a list of GDS supported vehicles.
- ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
- J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
- TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
- J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
- FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
- 【As a multi-protocol Pass-Thru vehicle interface】MaxiFlash Elite is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device. Specially designed to provide users with convenient PC communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, MaxiFlash Elite offers the most significant features desired by OEM customers: reliability, fast performance and flexibility.
- 【MaxiFlash Elite is an accessory tool for MK908P, MS908S Pro】Autel MaxiSys Elite to program ECUs on specific for BMW and for Benz vehicles, in case you lost the J-2534 programmer. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your tablet MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. The functions are NOT universally compatible. Please send VIN number to 🚘jmxd2022@outlook.com📧🚘 to check compatibility before your order. If need any supports, Please contact us.
- 【Wireless with advanced networking functions】Built-In Wireless with advanced networking functions and data storage. Fast performance ensures reprogramming even the newest controllers & Internet upgradable and updatable. Autel MaxiFlash Elite is compatiable with MaxiSYS MS908S, MaxiSYS MS908S Pro , MaxiSYS MS908CV, MaxiCOM MK908, MaxiCOM MK908 Pro, MaxiSYS Elite, MaxiSYS Elite II and Personal Computer
- 【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
- 【Supports simultaneous communication Definition in J2534-1】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed.Rugged aluminum case with non-slip rubber end caps, capable of withstanding harsh environment.
- 🔥【The King of Cost-Effectiveness From Autel】Fully upgraded from Autel MaxiSys EliteII /MS908S Pro/MK908P, Autel Scanner launched 2023 Newest 🅰🆄🆃🅴🅻 MaxiSys Elite II pro. 👉2 Years Free Update, ECU Programming&Coding, 38+ Service, Bidirectional Control, etc. Auto scanning 2.0 with all hardware parameters upgrade, provide total 8 (5+3)x diagnostic speed ✅CAN FD/ DOIP protocols support GM MY2020+ models, BMW E/F/G, Jaguar, Land Rover makes (Elite II can’t).
- 🔥【OE-LEVEL J2534 ECU PROGRAMMING & CODING】Enhance your diagnostics with the Elite II Pro J2534 Reprogramming scanner. This cutting-edge auto scanner supports : 1) program the new adaptive data to the on-board modules 2) replace the existing software/firmware in the ECUs 3) match the component control modules after repair or replacement 4) flash the hidden functions and 5) enhance the vehicle features. Experience 5X faster communication with SAE J2534-1 & -2 compliant programming interface.
- 🔥【38+ Maintenance Functions & High-End Functions】Autel scan tool Elite II Pro shares the same functional and deep service functions with other high-end scanners such as MaxiSys MS909/MS919/Ultra. 38+ special functions such as EPB/SAS/BMS/Oil/ABS/TPMS/Throttle/Injector/Suspension, etc., fix almost all “check engine” light issues. Bi-directional control, guided function, component matching, and scan VIN/license, together offer you effective and convenient diagnostic experiences.
- 🥇【DOIP& CAN FD Protocol, Top Hardware 5X Lightning Speed】Exclusive J2534 brings same DoIP & CAN FD protocol as Ultra/ MS919: CAN FD for GM MY2020+ Models; DOIP for BMW E/F/G Chassis, Jaguar, Land Rover makes. The improved hardware makes ELITE II PRO run more smoothly, even faster than MS919. It’s build with 8-Core CPU, Android 10.0 OS, 9.7’’ 1536*2048 touchscreen, 4GB&128GB, 11,000mAh battery, 2.4&5GHz dual-band WIFI, surpass Elite II/ Elite/ MS908S Pro II/ MK908 Pro II.
- 🔥【Free MV108 Assist Repairs】The MV108 digital inspection camera is designed to work with the MaxiSys series and PC, turning your MaxiSys scanner into a video inspection scope, allowing you to examine difficult-to-reach areas normally hidden from sight. It is capable of recording digital still images and videos, which offers you an economical solution to inspect machinery, facilities, and infrastructure quickly. One programmer tool Elite II Pro and one Videoscope MV108 make a perfect match.
- 🌐【Works with Autel MK908, MS908(S/Pro), MK908P, MaxiSys Elite】Autel J2534 work with these tools to program ECUs on specific BMW/ BENZ for specific functions. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your scanner MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, contact us via: 🚘auteldirect @ outlook. com🚘.
- 🌐【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
- 🌐【High-speed Transmission Speed】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed to save more times and win more business.
- 🌐【Multiple Devices Connected with PC】Autel MaxiFlash Elite J2534 also supports multiple device connections to the PC, which can operate diagnostic and reprogramming functions on more than one vehicle at the same time. Autel MaxiFlash Elite J2534 built-in wireless and data storage, which can update via Internet. It also ensures quickly reprogramming even the newest controllers.
- 🌐【Extensive Compatibility】Autel MaxiFlash J2534 is compatible with Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
- Industry-leading J2534 Pass-Thru Technology: Enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. Economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Each type (see single branded types above) Mongoose-Plus is engineered to work with one of the following OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, & VW/Audi.
- Supports Current & Earlier Vehicles: Enables diagnostics, programming and other “dealer” functions through OEM applications
- NEW Bluetooth Wireless Options Available: Providing wireless connectivity between your laptop and the Mongoose-Plus
- Expert Product Support: Staffed by technicians who understand vehicle repair and J2534 Pass‑Thru applications to help you with any technical setup questions
- Key Registration and Immobilizer Support: Using NASTF Vehicle Security Professional credentials
- Stay up-to-date with thelatest firmware and support of the SM2Pro J2534VCI ECUs programmer, ensuring reliable perform and optimalresults.
- The SM2Pro J2534VCI ECUs programmer is a trustedtool for professional technicians, offering comprehensive functionality and easy integration into your workflows.
- The SM2Pro J2534VCI ECUs programmer offersadvanced functionality for efficient and precise ECUs programming.
- With its 67IN1 without dongle & OBDcompatibility, the SM2Pro J2534VCI ECUs programmer provides a versatilesolution for read and write operations.
- Experienceseamless ECUs programming with the SM2Pro J2534VCI, designed to streamlines the read and write processes for enhanced efficiency.
Last update on 2024-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.