NHTSA ID Number: 10202397
Manufacturer Communication Number: PIT5291F
Summary
This Preliminary Information communication provides information to the technician about vehicle that may have wind whistle noise heard from the right or left rear quarter glass area when driving at highway speeds or with a cross wind. Technician will inspect the quarter glass for excessive urethane. If excessive urethane is found use a sharp knife and cut off the excessive urethane. Also the technician will install foam tape along the entire length of the tail light assembly.
Condition / Concern
Some owners may comment when driving at highway speeds (60 mph and up) there is a wind whistle noise heard from the right or left rear quarter glass area. This noise may be more noticeable with a cross wind.
SEOCONTENT-START
Bulletin No.: PIT5291F Published date: 09/20/2021 Preliminary Information PIT5291F Wind Whistle Noise at Highway Speeds from Left or Right Rear Quarter Glass Area Models Brand: Chevrolet
Chevrolet
GMC Model: Suburban Tahoe Yukon Models Model Years: 2015 – 2020 2015 – 2020 2015 – 2020 VIN: from to All All All All All All Engine: All All All All All All Transmissions: Supersession Statement This PI was superseded to add 2020 Model Year. Please discard PIT5291E. The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI. Condition / Concern Some owners may comment when driving at highway speeds (60 mph and up) there is a wind whistle noise heard from the right or left rear quarter glass area. This noise may be more noticeable with a cross wind. This concern could be caused by either of the following: 1. The fit between the exterior “D” pillar trim and the rear quarter glass in the area shown below. Excessive urethane from the quarter glass installation may not allow the exterior “D” pillar trim to fit properly against the rear quarter glass, as shown below. 2. The gap between the rear tail light assembly and the quarter panel, as shown below. Recommendations / Instructions 1. Use a sharp knife and cut off the excessive urethane, as shown below. In most cases the urethane will need to be cut sub-flush to the sheet metal. This will allow the exterior “D” pillar trim to fit correctly against the rear quarter glass. 2. Install a 5mm X 5mm (3/16 X 3/16) piece of closed cell foam tape along the entire length of the tail light assembly, as shown below. Warranty Information For vehicles repaired under the Bumper-to-Bumper coverage (Canada Base Warranty coverage), use the following labor operation. Reference the Applicable Warranties section of Investigate Vehicle History (IVH) for coverage information. Labor Operation Description Labor Time 1016250 Back Body Opening Side Molding Replacement (Condition 1) Use Published Labor Operation Time Labor Operation 2041150 Description Rear Body Structure Stop Lamp Replacement (Condition 2) Labor Time Use Published Labor Operation Time Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed. © 2021 General Motors
. All Rights Reserved.
SEOCONTENT-END
18 Affected Products
Vehicles
| MAKE | MODEL | YEAR |
| CHEVROLET | SUBURBAN | 2015-2020 |
| CHEVROLET | TAHOE | 2015-2020 |
| GMC | YUKON DENALI | 2015-2019 |
| GMC | YUKON XL | 2020 |
1 Associated Document
Manufacturer Communications
Bulletin No.: PIT5291F
Published date: 09/20/2021
MC-10202397-9999.pdf 1673.279KB
NHTSA ID Number: 10160978
Manufacturer Communication Number: PIT5291E
Summary
This Preliminary Information communication provides information to the technician about vehicle that may have wind whistle noise heard from the right or left rear quarter glass area when driving at highway speeds or with a cross wind. Technician will inspect the quarter glass for excessive urethane. If excessive urethane is found use a sharp knife and cut off the excessive urethane. Also the technician will install foam tape along the entire length of the tail light assembly.
Bulletin No.: PIT5291E
Published date: 05/3/2019
Bulletin No.: PIT5291C
Published date: 11/7/2017
Bulletin No.: PIT5291B
Date: Feb-2016
Bulletin No.: PIT5291A
Date: Jun-2014
Bulletin No.: PIT5291A
Date: June, 2014
Bulletin No.: PIT5291
Date: May-2014
Bulletin No.: PIT5291
Date: June, 2014
- Style your vehicle with luxury accessories
- Made of high quality polished 304 stainless steel with a UV stable, easy to maintain mirror black finish
- Custom fit panels for both sides of the vehicle install easily with pre-applied 3m automotive tape
- Made in the USA and backed by Putco's NeveRust lifetime warranty
- Kit contains 4 pieces
- Extended side column battery terminal bolt: The set includes extended side post battery terminal and Spacers. Used for side post bolt extender and wire directly hook up to battery
- Material: The terminal bolts of the side pillar battery are made of hard galvanized iron material, long service life. The structure is sturdy, corrosion-resistant, and durable
- Size: Thread 3/8", Bolt length: 1.6" (41mm)
- Easy to Install: Direct fit replacement unit, make it faster and easier for installation
- Widely Applicable: Suitable for cars, vehicles, RVs, and ships, etc. Also used for electrical equipment with 3/8 "-16 hole terminal blocks and requiring extension wires
- Extended side column battery terminal bolt: The set includes extended side post battery terminal and Spacers. Used for side post bolt extender and wire directly hook up to battery
- Material: The terminal bolts of the side pillar battery are made of hard galvanized iron material, long service life. The structure is sturdy, corrosion-resistant, and durable
- Size: Thread 3/8", Bolt length: 1.6" (41mm)
- Easy to Install: Direct fit replacement unit, make it faster and easier for installation
- Widely Applicable: Suitable for cars, vehicles, RVs, and ships, etc. Also used for electrical equipment with 3/8 "-16 hole terminal blocks and requiring extension wires
- Product Dimensions: This side post battery terminal extension bolt features standard 3/8"-16 coarse thread and 3/8"-24 fine thread sizes, compatible with common GM side pillar battery interfaces. Please carefully check the thread size specifications before ordering
- High-Quality Brass: The side post battery terminal extender body is made of high-quality solid brass, offering excellent conductivity and effectively reducing resistance and energy loss. Compared to ordinary aluminum or other metals, brass has stronger corrosion and oxidation resistance, preventing rust and making it suitable for long-term use in the complex environment of a car engine compartment
- Easy Installation: The battery terminal adapter bolts and nuts use a standard thread design with precise dimensions, requiring no special tools. Before installation, be sure to turn off the vehicle's power, then clean the surface of the battery terminal. Screw the nut into the fine-tooth end, align the bolt with the battery terminal hole, and tighten the stud until it is firmly attached to the terminal. Installation is simple and quick, saving you repair and installation time
- Multi-Purpose: This battery terminal bolt and nut kit is not only suitable for automotive side pillar batteries, but can also be used to connect audio amplifiers, vehicle power distributors, auxiliary batteries, marine or RV electrical systems, and many other applications, meeting the power supply and modification needs of multiple devices. It is highly practical and cost-effective
- Package Content: You will receive 2 side post battery terminal extension bolts and 2 matching nuts, allowing for simultaneous installation of both left and right battery terminals or use as spares, maintaining the stability of the vehicle's electrical system current
Last update on 2026-05-29 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.





