“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10198876
Manufacturer Communication Number: 21NA094
Summary
This service bulletin provides repair information to correct a customer concern of hood ajar message displayed on DIC, hood may not open using any electrical release buttons, but will open using manual release cable.
2 Affected Products
Vehicle
MAKE | MODEL | YEAR |
CHEVROLET | CORVETTE | 2020-2021 |
Condition
Some customers may comment on a hood ajar message displayed on the DIC. The hood may not open using any of the electrical release buttons but will open using manual release cable.
Cause
The cause of the condition may be any, or a combination of, the bullets listed below:
- Possible water intrusion and terminal corrosion into connector X103.
- Water intrusion into the hood latch actuator itself.
- Failure of the auxiliary hood latch release switch.
Correction
Verify the Condition and repair following the steps in the Service Procedure below.
Parts Information
Description | Part Number | Qty |
ACTUATOR ASM-HOOD LAT | 84806924 | 1 |
SWITCH ASM-HOOD LAT REL | 84720368 | 1, If necessary |
SEOCONTENT-START
Service Bulletin Bulletin No.: 21-NA-094
Date: May, 2021
TECHNICAL
Subject: Hood Ajar Message Displayed on Driver Information Center (DIC), Hood May Not Open
Using Any Electrical Release Buttons, But Will Open Using Manual Release Cable
Brand: Model:
Model Year: VIN:
Engine: Transmission:
from to from to
Chevrolet Corvette 2020 2021 — — All All
Involved Region or Country North America, Middle East, Japan
Condition
Some customers may comment on a hood ajar message displayed on the DIC. The hood
may not open using any of the electrical release buttons but will open using manual
release cable.
Cause
5795580
Page 2 May, 2021 Bulletin No.: 21-NA-094
5795581
The cause of the condition may be any, or a combination of, the bullets listed below:
• Possible water intrusion and terminal corrosion into connector X103.
• Water intrusion into the hood latch actuator itself.
• Failure of the auxiliary hood latch release switch.
Correction Verify the Condition and repair following the steps in the Service Procedure below.
Bulletin No.: 21-NA-094 May, 2021 Page 3
Service Procedure
5363245
1. Remove the front compartment front panel (1).
Refer to the appropriate Front Compartment Front
Panel Replacement in SI.
5795583
Page 4 May, 2021 Bulletin No.: 21-NA-094
2. Inspect connector X103 for possible terminal
corrosion.
• If corrosion IS noted at connector X103, replace
the connector as necessary. Refer to the
appropriate connector replacement procedure
in SI. After completion of the connector repair,
continue ahead to step # 3.
• If NO corrosion is noted at connector X103,
continue ahead to step # 3.
3. Access the hood switch connector (X102):
5795586
3.1. Remove the left horn (2). Refer to Horn
Replacement in SI.
5795588
3.2. Test the auxiliary hood latch release switch
with an ohmmeter. The switch should be open
when it’s not pressed and resistance should
be no more than .2 ohm, when the switch is
pressed.
• If the auxiliary hood latch release switch
passes the test, continue ahead to step
# 3.3.
• If the auxiliary hood latch release switch
fails the test, replace the switch. Refer to
Auxiliary Hood Latch Release Switch in SI.
After switch replacement, continue ahead
to step # 3.3.
3.3. Reinstall the left horn. Refer to Horn
Replacement in SI.
Bulletin No.: 21-NA-094 May, 2021 Page 5
5363519
4. Remove the hood latch actuator. Refer to the
appropriate Hood Latch Actuator Replacement
in SI.
Important: When reinstalling the front compartment
front panel, ensure that the X103 connector is
positioned below the right horn connector.
5. Install the new hood latch actuator service part.
Refer to the appropriate Hood Latch Actuator
Replacement in SI.
Parts Information
Causal
Part
Description Part
Number
Qty
X ACTUATOR
ASM-HOOD LAT 84806924 1
N/A SWITCH ASMHOOD
LAT REL 84720368 1, If
necessary
Warranty Information
For vehicles repaired under the Bumper-to-Bumper
coverage (Canada Base Warranty coverage), use the
following labor operation. Reference the Applicable
Warranties section of Investigate Vehicle History (IVH)
for coverage information.
Labor
Operation
Description Labor Time
1481538*
Hood Latch Actuator
Replacement, Includes
Test Auxiliary Hood Latch
Release Switch
1.7 hrs
Add
New Auxiliary Hood Latch
Release Switch
Replacement
1.0 hr
5430880 Connector with Leads
Assembly Replacement
Use Published
Labor
Operation
Time
*This is a unique Labor Operation for bulletin use only.
Version 1
Modified Released May 20, 2021
SEOCONTENT-END
1 Associated Document
Manufacturer Communications
Bulletin No.: 21-NA-094
Date: May, 2021
https://www.nhtsa.gov/recalls?nhtsaId=10198876
MC-10198876-9999.pdf 186.757KB
“This site contains affiliate links for which OEMDTC may be compensated” |
- Flagship product of a line of marine, industrial, aviation, automotive and other products
- Anti-Corrosion Aerosol and Lubricant
- Marine, industrial, aviation, automotive, concrete, asphalt and household maintenance, protection
- Quality craftsmanship and materials make this product a must have for any fisherman
- ZERO VOC minimal environmental impact formula
- Forms a dripless, dynamic, non-hardening, self-healing film that stubbornly resists erosion by splash or spray - including complete submersion in saltwater.
- Seals out moisture
- Unlike wax coatings, it will not dry out, stiffen or crack under stress
- Kills corrosion and keeps it from returning
- Safe on electronics
- STOPS RUST AND CORROSION with unique Polar Bonding and Fluid Thin Film Coating (FTFC) Technologies
- BREAKTHROUGH LUBRICANT sticks to metal like a magnet to resist displacement by friction or pressure. Lubricates under extreme loads and high temperatures.
- AMAZING PENETRANT & ANTI-SEIZE penetrates faster and further to break free rusted nuts, bolts and fittings within minutes
- SAFE ON ELECTRONICS displaces moisture and protects electronics with a self-healing high dielectric Fluid Thin Film Coating that won’t interfere with circuits
- ZERO VOC minimal environmental impact formula
- STOPS RUST AND CORROSION with unique Polar Bonding and Fluid Thin Film Coating (FTFC) Technologies
- BREAKTHROUGH LUBRICANT sticks to metal like a magnet to resist displacement by friction or pressure. Lubricates under extreme loads and high temperatures.
- AMAZING PENETRANT & ANTI-SEIZE penetrates faster and further to break free rusted nuts, bolts and fittings within minutes
- SAFE ON ELECTRONICS displaces moisture and protects electronics with a self-healing high dielectric Fluid Thin Film Coating that won’t interfere with circuits
- ZERO VOC minimal environmental impact formula
- Forms a dripless, dynamic, non-hardening, self-healing film that stubbornly resists erosion by splash or spray - including complete submersion in saltwater.
- Seals out moisture
- Unlike wax coatings, it will not dry out, stiffen or crack under stress
- Kills corrosion and keeps it from returning
- Safe on electronics
- Stops rust and corrosion
- Extended water / weather resistance
- Safe in electronics
- Designed to withstand extreme corrosive environments including sulphuric and direct saltwater spray.
- CUTS THROUGH STUBBORN BORE DEPOSITS for easier, more thorough cleaning. Shields bore from powder residue, primer salts and metal particle buildup.
- STICKS TO METAL LIKE A MAGNET, so it cannot be displaced by moisture, friction or extreme pressures. Lubricates better and longer than other gun oils – virtually eliminating wear and providing flawless action.
- 3X THE ANTI-WEAR PROTECTION of MilSpec CLPs. Nearly 2X the load carrying capacity of Mil Spec CLPs.
- FAMOUS CORROSIONX RUST PREVENTION. Best-on-class Durability. Molecular Level Cleaning.
- STOPS CORROSION and rust – even in the rain!
- QUALIFIED under U.S. military performance requirement MIL-PRF-81309H
- MILITARY TESTED AND PROVEN over 2X as effective than other corrosion prevention and control products
- CORROSIONX POLAR BONDING TECHNOLOGY
- Self-curing Fluid Thin Film Coating (FTFC) technology
- ZERO VOC minimal environmental impact product
- Forms a dripless, dynamic, non-hardening, self-healing film that stubbornly resists erosion by splash or spray - including complete submersion in saltwater.
- Seals out moisture
- Unlike wax coatings, it will not dry out, stiffen or crack under stress
- Kills corrosion and keeps it from returning
- Safe on electronics
- Nontoxic, non-carcinogenic, nonflammable and environmentally friendly
- Self-curing Fluid Thin Film Coating (FTFC) technology
- CORROSIONX POLAR BONDING TECHNOLOGY
- ZERO VOC minimal environmental impact product
Last update on 2024-04-16 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.