“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10184111
Manufacturer Communication Number: PIC6337A
Summary
This Preliminary Information communicates an additional location and condition for technicians to look at when diagnosing an exhaust rattle noise.
SEOCONTENT-START
Bulletin No.: PIC6337A Published date: 11/16/2020
Preliminary Information
PIC6337A Rattle Noise from Exhaust
Models
Brand: | Model: | Model Years: | VIN: | Engine: | Transmissions: | |
from | to | |||||
Chevrolet | Camaro | 2018 – 2021 | All | All | LGX | All |
Involved Region or Country | North America |
Condition | Some customers may comment about an exhaust rattle coming from the vehicle. Many technicians will automatically look at the exhaust valves for noise concerns. Before any repair is made, dealership technicians should also look at the resonator for the source of this concern. There is a tube that is located in the center of the resonator that can be seen in the first photo below. This is NOT a drain tube for condensation inside the exhaust system. This pipe is actually a structural component of the resonator that stiffens the upper and lower halves of the assembly. The welds holding this tube in place may crack, resulting in a rattle noise that can be heard by the owner of the vehicle. This will be most noticeable when starting the engine / applying the throttle.
Note: Corrosion alone will not cause this concern. The quality of the actual welds is the issue. Dealership technicians are to inspect both the lower weld on the bottom of the resonator, as well as the upper weld on top of the resonator for signs of cracking. |
Correction:
If the concern listed above has been found, dealership technicians are to replace the rear portion of the exhaust system.
Warranty Information
For vehicles repaired under the Bumper-to-Bumper coverage (Canada Base Warranty coverage), use the following labor operation. Reference the Applicable Warranties section of Investigate Vehicle History (IVH) for coverage information.
Labor Operation | Description | Labor Time |
4051530 | Exhaust Mufler Replacement | Use Published Labor Time |
*This is a unique Labor Operation for Bulletin use only. |
Version History
Version | 1 |
Modified | 07/18/2018 – Created on.
11/16/2020 – Updated Models |
SEOCONTENT-END
4 Affected Products
Vehicle
MAKE | MODEL | YEAR |
CHEVROLET | CAMARO | 2018-2021 |
1 Associated Document
Manufacturer Communications
Bulletin No.: PIC6337A
Published date: 11/16/2020
https://www.nhtsa.gov/recalls?nhtsaId=10184111
MC-10184111-9999.pdf 1336.243KB
“This site contains affiliate links for which OEMDTC may be compensated” |
- ✔️ All of Our Items are 100% In Original Packaging! You Will Never Receive a Used Item From Us!
- ✔️ Items are Exactly the Same as Shown in the Images! You Will Receive the Exact Item You Purchased!
- ✔️ Installation Made Easy on All of Our Items! Little to No Modifications needed at Best!
- ✔️ 30 Days Refund & 90 Days Defective Item Replacement Warranty! Any Issues With Your Item Please Call/Email Us and We Will Help You!
- ✔️ FITMENT: Compatible with Chevy Camaro 3.6L V6 engine 2010-2015 models only.
- Vehicle Compatibility - Axle-back exhaust system compatible with Chevrolet Camaro 2010-2015, fits with 6.2L models.
- Brilliant Performance - Come with [2] high performance racing design exit axle-back exhaust, can maximize to enhance the high exhaust air flow rate without sacrificing the attractive power sound in the smoothest conditions.
- Extraordinary Quality - It is constructed of high quality aluminized steel with computerized mandrel-bends for the strength and durability, and the TIG welded CNC machine can resistant against pressure and corrosion.
- Simple Installation - Fast and easy for the installation, can make you enjoy the best performance in the fastest time.
- Product Specification - Major Piping: 2.5" OD | Muffler Exhaust Tip: 4" OD | Inlet: 2.5" OD | Outlet: 2.5" OD | Weight: 33 LBS | Muffler Tip Type: Round Diagonal Cut Rolled Lip
- Item Package Dimension: 27.0L x 10.0W x 9.0H inches
- Item Package Weight - 36.80 Pounds
- Item Package Quantity - 1
- Product Type - MUFFLER
- 【FITMENT】Compatible with 10-15 Chevy Camaro 6.2L
- 【Quality Construction】Made of High Quality T-304 Stainless Steel with Computerized Mandrel-Bends for Strength and Durability
- 【Enhance Performence】Dyno proven to instantly increases 15 - 25 horsepower / low end torque. Aggressive deep and smooth tone while ensures smooth exhaust gas flow, increase engine output and efficiency.
- 【Long Term Durability】TIG welded CNC machine flange for resistance against pressure and corrosion.
- 【Design】The larger pipes, low-restriction mufflers, and tuned resonators of a well-designed performance exhaust system can make stunned effect on your vehicle: lower auto exhaust back pressure and a much better sound.
- ✔️ All of Our Items are 100% In Original Packaging! You Will Never Receive a Used Item From Us!
- ✔️ Items are Exactly the Same as Shown in the Images! You Will Receive the Exact Item You Purchased!
- ✔️ Installation Made Easy on All of Our Items! Little to No Modifications needed at Best!
- ✔️ 30 Days Refund & 90 Days Defective Item Replacement Warranty! Any Issues With Your Item Please Call/Email Us and We Will Help You!
- ✔️ FITMENT: Compatible with Chevy Camaro 3.6L V6 engine 2010-2015 models only.
- AXLE-BACK EXHAUST - Oval Style Mufflers; 4" Double Walled Round Diagonal Cut 304 Stainless Steel Polished; Inlet Size: 2.5" OD / Major Diameter: 3" OD / Outlet Size : 4" OD
- FITMENT - Compatible with Chevrolet Camaro 6.2L 10-15
- STRENGTH CONSTRUCTION -Made of High Quality Aluminized Steel with Computerized Mandrel-Bends for Strength and Durability; TIG Welded CNC Machine for Resistance against Pressure and Corrosion
- INSTALLATION - Slip Fit Piping / Clamp On Design; High Performance Racing Spec. Design; can Make you enjoy the Best Performance in the Fastest Time
- NOTE - Professional Installation is Highly Recommended; Installation Instruction is NOT Included.
- T-304 Stainless Steel
- Bolt On Installation
- All Welded Construction
- Made In USA
- Classic BORLA Sound
- T-304 Stainless Steel
- Bolt On Installation
- All Welded Construction
- Made In USA
- Classic BORLA Sound
- T-304 Stainless Steel
- Bolt On Installation
- All Welded Construction
- Made In USA
- No Drone Guarantee
- T-304 Stainless Steel
- Bolt On Installation
- All Welded Construction
- Made In USA
- No Drone Guarantee
Last update on 2024-07-08 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.