Product Safety Recall 17276 Loss of Steering Assist – 2014 Chevrolet Silverado & GMC Sierra 1500

“This site contains affiliate links for which OEMDTC may be compensated”

June 29, 2017 NHTSA CAMPAIGN NUMBER: 17V414000

Temporary Loss of Electric Power Steering (EPS)

If EPS assist is lost and then returns, the driver might lose temporary control of the steering wheel, increasing the risk of a crash.

 

NHTSA Campaign Number: 17V414

Manufacturer General Motors LLC

Components STEERING

Potential Number of Units Affected 690,685

 

Summary

General Motors LLC (GM) is recalling certain 2014 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles. The vehicles may have a temporary loss of electric power steering (EPS) assist, especially during low-speed turning maneuvers.

 

Remedy

GM will notify owners, and dealers will update the EPS module software, free of charge. The recall began on August 10, 2017. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-432-8782. GM’s number for this recall is 17276.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 

Check if your Vehicle has a Recall

 


 


“This site contains affiliate links for which OEMDTC may be compensated”

Closed Product Field Actions Re-Opened Due to Missing or Invalid Warranty Claim Codes Recalls 15176, 15240, 15299, 15808, 16007, 17130, 17276, 17287 and 45340  

A warranty audit of paid transactions for the safety and noncompliance recalls identified above revealed that some transactions were submitted without a Warranty Claim Code (WCC) or with an incorrect WCC.  This code is generated when a control module is successfully programmed using the TIS Service Programming System (SPS).  Since these transactions were identified as not having a valid WCC, the status of the involved vehicles was changed from “closed” to “open” in the Required Field Actions section of Investigate Vehicle History (IVH).  Dealer message GCUS-3-1280 dated June 26, 2018 provides additional details (see attached copy).

 

Q1: Will these transactions be debited?

No, only the field action is being re-opened in IVH in the interest of customer safety.  However, some previous transactions for recall 15299 were re-opened and debited on March 16, 2018.  These transactions are now being worked by the Warranty Support Center (WSC) to cancel the debits and re-credit the affected dealers.  Future transactions that do not contain a valid WCC may be debited, if dealers do not take appropriate actions resolve this situation.

Q2: What if a dealer can’t locate the current vehicle owner?

If the current vehicle owner cannot be located, no further action is necessary.  GM uses state vehicle registration records to regularly update owner of record information for open field actions.  These updates are available on the Open Vehicle Report (OVR), which is posted monthly in GM GlobalConnect.  Product field action reminder notices are also mailed to the new vehicle owners as they are identified.

Q3: Will a dealer be paid to program a vehicle a second time?

Yes, if a second programming event is required, dealers should open a new job card and re-use the labor code and labor time from the applicable bulletin.  To facilitate this activity, an update was made in Service Programming System (SPS) which allows a technician to override the “same calibration” warning on these specific recall reprogramming events.  This provides the ability to perform the second programming event and obtain a new WCC.

Q4: If another dealer was originally involved, can any dealer perform the second programming event and how do they get paid?

Performance of the second programming event is not restricted to the dealer who performed the original programming event and did not submit a valid WCC.  In such cases, dealers should submit a transaction as they normally do, using the labor code and labor time from the applicable bulletin.  The first dealer to submit a transaction with a valid WCC will be paid and the recall will be closed in IVH.  Exceptions will be addressed on a case-by-case basis by the GM Warranty Support Center (WSC).

Q5: If a valid WCC is retrievable from dealer records, can the original transaction be adjusted in the GWM system?

Yes, if the original transaction was processed within the past 2 years, the transaction can be adjusted (adding the WCC) on-line in the GWM system.  Dealers should not use their Dealer Management System (DMS) to do this.

 

Q6: If a dealer has a valid WCC and is re-submitting an original transaction that is less than 2 years old, are they entitled to labor time?

As a technician is not required in this case, dealers are not entitled to claim additional labor time. A dealer however may submit a $20.00 administrative allowance as compensation for processing the second transaction.  After adding the WCC to the original transaction’s “SPS Warranty Claim Code” field the dealer may add $20.00 to the Net Item/Admin Allowance field and resubmit the transaction.

Q8: What should a dealer do if they have a valid WCC, but the original transaction is over 2 years old?  Can they resubmit the transaction?

No, the dealer should create a new job card making sure to use all the information from the first job card (open date, mileage and technician code, etc.).  After adding the WCC to the transaction’s “SPS Warranty Claim Code” field and $20.00 to the Net Item/Admin Allowance field, the dealer should submit the new transaction.

Q9: What should a dealer do if a valid WCC is not retrievable from dealer records?

If a valid WCC was not recorded on the shop copy of the job card and/or is not retrievable from the SPS history log, the involved vehicle must be reprogrammed to generate a new WCC.  Using the labor code and labor time provided in the bulletin, the dealer should create a new job card.  Note that the dealer is entitled to whatever time is listed in the bulletin, but not the $20.00 administrative allowance.  Upon completion of this second programming event, the dealer should submit the new transaction making sure to include the new WCC.

Q10: Will the system reject these transactions due to age or mileage?

There is no “over-age” or “mileage rollback” edit in place for the resubmission of these transactions, so they should pay without the need for wholesale authorization.

SEOCONTENT-END


2 Affected Products

Vehicles

MAKE MODEL YEAR
CHEVROLET SILVERADO 1500 2014
GMC SIERRA 1500 2014

 


28 Associated Documents

Manufacturer Notices(to Dealers,etc) – Date: June 29, 2017 Subject: Stop Delivery Order for Upcoming Safety Recall 17276

RCMN-17V414-8674.pdf 72.101KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [70.41 KB]

 


Defect Notice 573 Report

RCLRPT-17V414-2815.PDF 216.316KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [211.25 KB]

 


Recall 573 Report-Amendment 2

RCLRPT-17V414-9168.PDF 216.396KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [211.32 KB]

 


Recall Acknowledgement

RCAK-17V414-5257.pdf 247.865KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [242.06 KB]

 


Recall 573 Report-amendment 1

RCLRPT-17V414-4300.PDF 216.372KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [211.30 KB]

 


Manufacturer Notices(to Dealers,etc) – Date: July 13, 2017 Subject: Upcoming Safety Recall 17276

RCMN-17V414-0790.pdf 132.599KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [129.49 KB]

 


ISSUED Owner Notification Letter(Part 577)

RCONL-17V414-9025.pdf 91.344KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [89.20 KB]

 


ISSUED Owner Notification Letter(Part 577)

RCONL-17V414-2962.pdf 91.344KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [89.20 KB]

 


Recall Quarterly Report #2, 2017-4

RCLQRT-17V414-6431.PDF 214.633KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [209.60 KB]

 


Manufacturer Notices(to Dealers,etc) – Date: August 7, 2017 Subject: 17276 – Safety Recall Loss of Steering Assist

RCMN-17V414-2053.pdf 6.852KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [6.69 KB]

 


Safety Bulletin – Reference Number: N172085440 Release Date: August 2017

RCSB-17V414-6829.pdf 292.749KB

To View or Download this Document Click Here

 

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [285.89 KB]

 


Recall Quarterly Report #1, 2017-3

RCLQRT-17V414-0238.PDF 214.522KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [209.49 KB]

 


Manufacturer Notices(to Dealers,etc) – Date: August 10, 2018 Subject: 17276-02 – Safety Recall Loss of Steering Assist Revised Service Procedure section

RCMN-17V414-9511.pdf 8.979KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [8.77 KB]

 


Manufacturer Notices(to Dealers,etc) – Date: August 10, 2018 Subject: 17276-02 – Safety Recall Loss of Steering Assist Revised Service Procedure section

RCMN-17V414-6593.pdf 8.979KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [8.77 KB]

 


Dealer FAQs 16Jul2018

RMISC-17V414-6025.pdf 136.796KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [133.59 KB]

 


Safety Bulletin – Reference Number: N172085440 Release Date: May 2018 Revision: 01

RCSB-17V414-6986.pdf 197.382KB

To View or Download this Document Click Here

 

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [192.76 KB]

 


Safety Bulletin – Reference Number: N172085440 Release Date: August 2018 Revision: 02

RCSB-17V414-0474.pdf 366.21KB

To View or Download this Document Click Here

 

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [357.63 KB]

 


Manufacturer Notices(to Dealers,etc) – Date: October 11, 2018 Subject: Reopened Recalls Involving Module Reprogramming Events

RCMN-17V414-7288.pdf 20.62KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [20.14 KB]

 


Manufacturer Notices(to Dealers,etc) – Date: June 26, 2018 Subject: Select Safety and Noncompliance Recalls Closed Transactions Reopened Due to Warranty Audit See Table Below

RCMN-17V414-0647.pdf 105.234KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [102.77 KB]

 


Manufacturer Notices(to Dealers,etc) – Date: June 26, 2018 Subject: Select Safety and Noncompliance Recalls Closed Transactions Reopened Due to Warranty Audit

RCMN-17V414-3809.pdf 201.176KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [196.46 KB]

 


Manufacturer Notices(to Dealers,etc) – Date: July 16, 2018 Subject: Service Programming System Warranty Claim Code Audit Frequently Asked Questions (FAQs)

RCMN-17V414-0776.pdf 9.531KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [9.31 KB]

 


Reopened Recalls Involving Module Reprogramming Events – FAQs

RMISC-17V414-3089.pdf 71.752KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [70.07 KB]

 


Safety Bulletin – Reference Number: N172085440 Release Date: August 2018 Revision: 02

RCSB-17V414-6758.pdf 366.21KB

To View or Download this Document Click Here

 

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [357.63 KB]

 


Recall Quarterly Report #6, 2018-4

RCLQRT-17V414-7158.PDF 211.678KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.72 KB]

 


Recall Quarterly Report

RCLQRT-17V414-7486.PDF 214.845KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [209.81 KB]

 


Recall Quarterly Report #3, 2018-1

RCLQRT-17V414-2985.PDF 214.741KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [209.71 KB]

 


Manufacturer Notices(to Dealers,etc) – Date: May 30, 2018 Subject: 17276-01 – Safety Recall Loss of Steering Assist Revised Warranty and Service Procedure sections

RCMN-17V414-9210.pdf 9.629KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [9.40 KB]

 


Recall Quarterly Report #5, 2018-3

RCLQRT-17V414-3944.PDF 211.587KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.63 KB]

 


Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=17V414&docType=RCL



 


 

Reprogramming

GM Diagnostic/Programming (TIS2Web)

 

Approved J2534 Device with TIS2WEB can reprogram 1996 and later All GM Modules.

To obtain the latest electronic controller calibration information for your vehicle, go to https://tis2web.service.gm.com/tis2web and enter the vehicle's 17 character Vehicle Identification Number (VIN) and select 'Get CAL ID’.

You can then compare the latest part number with the actual number installed on the vehicle to determine if a reprogram is needed.

The Service Programming System (SPS) application is part of the TIS2Web system. To program an ECU, the SPS application must communicate with the vehicle control modules using the proper J2534 programming interface tool.

The following are the supported interface tools:

 
 
 
Bosch Automotive Tools MTECH2 Mastertech II J2534 VCI with Wired/Wireless Capability for OEM Reprogramming and Diagnostics on GM, Ford, FCA, Nissan/Infiniti, Honda/Acura, and Toyota/Lexus Vehicles
CarDAQ-M Auto Universal Diagnostic Scanner and Programming Tool VSI J2534
Drew Technologies (DRWCDPLUSKIT) CarDAQ-Plus J2534 Flash Reprogramming Kit
CarDAQ-Plus 3 All Makes J2534 Reprogramming Tool
RAP2 OEM J2534 Remote Reprogramming Tool
Drew Technologies (DRWMONGGM) Mongoose GM Vehicle Interface (VPW/CAN) J2534
Mongoose-Plus J2534 OEM Vehicle Interface Cable - GM OEM Reprogramming and Diagnostics
Autel MaxiFlash Elite VCI J2534 Pass-Thru ECU Programming Tool
Mongoose-Plus J2534 OEM Vehicle Interface Cable - OEM Reprogramming and Diagnostics for GM
BOSCH Automotive Tools MTECH2 Mastertech II J2534 VCI
Autel MaxiFlash VCI Vehicle Communication Interface J2534 PassThru ECU Programming Device Bluetooth Connection Internet Update Support CAN FD, 4 CAN Channels, DoIP, D-PDU Works with PC or Autel MS909
VXDIAG VCX Nano Compatible for GM/OPEL with GDS2 and Tech2WIN System Diagnostic Tool
GODIAG J2534

 

The Tech 2 supports model years 1996 and beyond. With the addition of the CAN Diagnostic Interface (CANdi) module, Tech 2 is fully backward compatible with current Tech 2 functionality and operates transparently when diagnosing non-CAN-equipped vehicles.

Servicing the next generation Global A vehicles will require the diagnostic software, GDS2, Global Diagnostic System 2 running on a local PC device while the MDI is connected to the vehicle. The GM MDI is the Global Diagnostic tool for future vehicles starting with Global A vehicles.

The GM MDI was introduced in the fall of 2007 for Pass-Thru programming and offers faster programming speed. It can be used to perform Pass-Thru programming on all vehicles built since 1996 and into the future. Click here to view a list of GDS supported vehicles.

www.acdelcotds.com

 


 

Bestseller No. 1
CarDAQ-Plus 3 All Makes J2534 Reprogramming Tool
  • ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
  • J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
  • TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
  • J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
  • FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
Bestseller No. 2
Autel MaxiFlash Elite VCI J2534 Pass-Thru ECU Programming Tool, Vehicle Communication Interface,Work with Autel MaxiSYS Elite II, Elite, MS908, MS908S Pro, MK908 Pro II, MS908CV, MK908P and PC
  • 【As a multi-protocol Pass-Thru vehicle interface】MaxiFlash Elite is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device. Specially designed to provide users with convenient PC communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, MaxiFlash Elite offers the most significant features desired by OEM customers: reliability, fast performance and flexibility.
  • 【MaxiFlash Elite is an accessory tool for MK908P, MS908S Pro】Autel MaxiSys Elite to program ECUs on specific for BMW and for Benz vehicles, in case you lost the J-2534 programmer. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your tablet MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. The functions are NOT universally compatible. Please send VIN number to 🚘jmxd2022@outlook.com📧🚘 to check compatibility before your order. If need any supports, Please contact us.
  • 【Wireless with advanced networking functions】Built-In Wireless with advanced networking functions and data storage. Fast performance ensures reprogramming even the newest controllers & Internet upgradable and updatable. Autel MaxiFlash Elite is compatiable with MaxiSYS MS908S, MaxiSYS MS908S Pro , MaxiSYS MS908CV, MaxiCOM MK908, MaxiCOM MK908 Pro, MaxiSYS Elite, MaxiSYS Elite II and Personal Computer
  • 【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
  • 【Supports simultaneous communication Definition in J2534-1】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed.Rugged aluminum case with non-slip rubber end caps, capable of withstanding harsh environment.
Bestseller No. 3
Autel MaxiSys Elite II Pro: 2024 Top 2-Years Free Updates Scanner, Same as MS Ultra w/ J2534 ECU Reprogramming & OE Coding, Bidirectional Control, 38+ Reset Service, CANFD& DoIP, FCA Autoauth & SGW
  • 🔥【The King of Cost-Effectiveness From Autel】Fully upgraded from Autel MaxiSys EliteII /MS908S Pro/MK908P, Autel Scanner launched 2023 Newest 🅰🆄🆃🅴🅻 MaxiSys Elite II pro. 👉2 Years Free Update, ECU Programming&Coding, 38+ Service, Bidirectional Control, etc. Auto scanning 2.0 with all hardware parameters upgrade, provide total 8 (5+3)x diagnostic speed ✅CAN FD/ DOIP protocols support GM MY2020+ models, BMW E/F/G, Jaguar, Land Rover makes (Elite II can’t).
  • 🔥【OE-LEVEL J2534 ECU PROGRAMMING & CODING】Enhance your diagnostics with the Elite II Pro J2534 Reprogramming scanner. This cutting-edge auto scanner supports : 1) program the new adaptive data to the on-board modules 2) replace the existing software/firmware in the ECUs 3) match the component control modules after repair or replacement 4) flash the hidden functions and 5) enhance the vehicle features. Experience 5X faster communication with SAE J2534-1 & -2 compliant programming interface.
  • 🔥【38+ Maintenance Functions & High-End Functions】Autel scan tool Elite II Pro shares the same functional and deep service functions with other high-end scanners such as MaxiSys MS909/MS919/Ultra. 38+ special functions such as EPB/SAS/BMS/Oil/ABS/TPMS/Throttle/Injector/Suspension, etc., fix almost all “check engine” light issues. Bi-directional control, guided function, component matching, and scan VIN/license, together offer you effective and convenient diagnostic experiences.
  • 🥇【DOIP& CAN FD Protocol, Top Hardware 5X Lightning Speed】Exclusive J2534 brings same DoIP & CAN FD protocol as Ultra/ MS919: CAN FD for GM MY2020+ Models; DOIP for BMW E/F/G Chassis, Jaguar, Land Rover makes. The improved hardware makes ELITE II PRO run more smoothly, even faster than MS919. It’s build with 8-Core CPU, Android 10.0 OS, 9.7’’ 1536*2048 touchscreen, 4GB&128GB, 11,000mAh battery, 2.4&5GHz dual-band WIFI, surpass Elite II/ Elite/ MS908S Pro II/ MK908 Pro II.
  • 🔥【Free MV108 Assist Repairs】The MV108 digital inspection camera is designed to work with the MaxiSys series and PC, turning your MaxiSys scanner into a video inspection scope, allowing you to examine difficult-to-reach areas normally hidden from sight. It is capable of recording digital still images and videos, which offers you an economical solution to inspect machinery, facilities, and infrastructure quickly. One programmer tool Elite II Pro and one Videoscope MV108 make a perfect match.
Bestseller No. 4
Autel MaxiFlash Elite VCI J2534 Pass-Thru ECU Programming Tool, Multi-Protocol PassThru Interface, Work with Autel MaxiSYS Elite II, Elite, MS908, MS908S Pro, MS908CV, MK908P, MK908 Pro II and PC
  • 🌐【Works with Autel MK908, MS908(S/Pro), MK908P, MaxiSys Elite】Autel J2534 work with these tools to program ECUs on specific BMW/ BENZ for specific functions. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your scanner MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, contact us via: 🚘auteldirect @ outlook. com🚘.
  • 🌐【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
  • 🌐【High-speed Transmission Speed】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed to save more times and win more business.
  • 🌐【Multiple Devices Connected with PC】Autel MaxiFlash Elite J2534 also supports multiple device connections to the PC, which can operate diagnostic and reprogramming functions on more than one vehicle at the same time. Autel MaxiFlash Elite J2534 built-in wireless and data storage, which can update via Internet. It also ensures quickly reprogramming even the newest controllers.
  • 🌐【Extensive Compatibility】Autel MaxiFlash J2534 is compatible with Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
Bestseller No. 5
Mongoose-Plus J2534 OEM Vehicle Interface Cable - Ford/Lincoln/Mercury OEM Reprogramming and Diagnostics
  • Industry-leading J2534 Pass-Thru Technology: Enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. Economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Each type (see single branded types above) Mongoose-Plus is engineered to work with one of the following OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, & VW/Audi.
  • Supports Current & Earlier Vehicles: Enables diagnostics, programming and other “dealer” functions through OEM applications
  • NEW Bluetooth Wireless Options Available: Providing wireless connectivity between your laptop and the Mongoose-Plus
  • Expert Product Support: Staffed by technicians who understand vehicle repair and J2534 Pass‑Thru applications to help you with any technical setup questions
  • Key Registration and Immobilizer Support: Using NASTF Vehicle Security Professional credentials
Bestseller No. 6
Latest Version ECUs Programmer SM2Pro J2534VCI Read Write 67IN1 Dongle Suiatble for Efficient ECUs Programming Durable Diagnostic Tool Plastic ECUs Programmer Vehicle Repair Tool Engine Diagnostic
  • Stay up-to-date with thelatest firmware and support of the SM2Pro J2534VCI ECUs programmer, ensuring reliable perform and optimalresults.
  • The SM2Pro J2534VCI ECUs programmer is a trustedtool for professional technicians, offering comprehensive functionality and easy integration into your workflows.
  • The SM2Pro J2534VCI ECUs programmer offersadvanced functionality for efficient and precise ECUs programming.
  • With its 67IN1 without dongle & OBDcompatibility, the SM2Pro J2534VCI ECUs programmer provides a versatilesolution for read and write operations.
  • Experienceseamless ECUs programming with the SM2Pro J2534VCI, designed to streamlines the read and write processes for enhanced efficiency.

Last update on 2024-04-17 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

2 thoughts on “Product Safety Recall 17276 Loss of Steering Assist – 2014 Chevrolet Silverado & GMC Sierra 1500”

  1. On December 21, 17. My vehicle had this happen to me.
    Wow thought it was just a simple recall fix I had fixed on November 1, 2017. Oh they say it’s fixed But was I wrong. Last Thursday this happened to me When I was turning off of Kings rd in Clt Nc. Scared to death to drive my truck now. Last week out of no where the truck turns off, steering wheel locks while I’m turning and I have no control while I’m driving. Gm needs to buy back my truck. Truck is at dealership now. What do I do. No wonder I can’t sleep. Worried
    I am talking with GM and waiting to see what they are going to do ????????.

    Reply
  2. Product Safety Recall 17276. Loss of Steering Assist Reprogramming. I called the nearest dealer for an appointment. On Friday October 27, 2017 I delivered my GMC to the dealer for the recall fix. My route was all smooth, paved roads at the posted speed limits. The limit was 70 mph on the highway portion. About three miles. About five miles total drive. I experienced no problems with steering or anything else. I left my vehicle for servicing and returned that afternoon to pick it up. I was notified by phone that my vehicle was ready to be picked up shortly after I left it there for the recall. When I picked my vehicle up I drove the same route to return home. At 70 mph I experienced a slight vibration in the steering wheel and a funny noise that I had never heard before. I turned around and drove back to the dealer. I told the Service guy that there was something wrong and explained. He said something about all they did was program a module. I said my vehicle was not doing what I described when I brought it in. He went to find someone to test drive. I went with the guy. He said he did not feel anything and said I probably needed to have my front end aligned. Back at the dealership there were three people waiting on me. One was probably a supervisor. He was more interested in covering the dealership than my problem. I felt intimidated with the three there waiting on me and felt like they were trying to cover their rears for some reason. I left with their statement that all that was done was reprogram a module. Has anyone else out there had a similar experience with this recall fix?

    Reply

Leave a Reply to Julian Lee Hurd Cancel reply

Share to...