“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10143749
Manufacturer Communication Number: 16186 01
Summary
16186-01 – Emission Recall. On certain vehicles equipped with a 1.8L engine (RPO LWE), cracking of ceramic components internal to the catalytic converter may occur as a result of higher than anticipated exhaust temperatures. If this occurs, the catalytic converter low efficiency diagnostic will set and the malfunction indicator lamp will illuminate. Dealers are to reprogram the engine control module with calibrations that prevent higher than expected exhaust temperatures. (service procedure revised)
4 Affected Products
Vehicles
MAKE | MODEL | YEAR |
CHEVROLET | CRUZE | 2013-2014 |
CHEVROLET | SONIC | 2013-2014 |
SEOCONTENT-START
Bulletin No.: 16186-01
Date: June 2018
Subject: | Catalytic Converter Internal Damage |
Models: | 2013–2014 Chevrolet Cruze |
2013–2014 Chevrolet Sonic | |
Equipped with 1.8L Engine (RPO LWE) |
Reference Number: | A162049350 | Release Date: | June 2018 |
Revision: | 01 | ||
Revision Description: This bulletin has been revised to remove the Module Programming Not Required labor code from the Warranty Information section and to update the Service Procedure. Effective immediately, technicians MUST record the Warranty Claim Code on the Job Card. To avoid warranty transaction rejection, this information must be entered when submitting the transaction. If the Same Calibration/Software Warning is noted on the SPS Controller screen, continue with the programming event using SPS to ensure a Warranty Claim Code is displayed on screen. Please discard all copies of bulletin 16186. |
Make | Model | Model Year | RPO | Description | |
---|---|---|---|---|---|
From | To | ||||
Chevrolet | Cruze | 2013 | 2014 | LWE | 1.8L Engine |
Chevrolet | Sonic | 2013 | 2014 | LWE | 1.8L Engine |
Involved vehicles are identified on the Applicable Warranties section in GM Global Warranty Management system. This site should always be checked to confirm vehicle involvement prior to beginning any required inspections and/or repairs.
Condition | General Motors has decided to conduct a Voluntary Emission Recall on certain 2013-2014 model year Chevrolet Cruze and Sonic vehicles equipped with a 1.8L (RPO LWE) engine. On some vehicles, cracking of ceramic components internal to the catalytic converter may occur as a result of higher than anticipated exhaust temperatures. If this occurs, the catalytic converter low efficiency diagnostic will set and the malfunction indicator lamp will illuminate. |
Correction | Dealers are to reprogram the engine control module with calibrations that prevent higher than expected exhaust temperatures. |
Parts Information
No parts are required for this procedure.
Warranty Information
Labor Code | Description | Labor Time | Trans. Type | Net Item |
9102906* | Engine Control Module Reprogramming with SPS Sonic | 0.3 | ZFAT | N/A |
9102910* | Engine Control Module Reprogramming with SPS Cruze | 0.4 | ZFAT | N/A |
9102967 | Customer Reimbursement Approved | N/A | ZFAT | ** |
9102968 | Customer Reimbursement Denied | N/A | ZFAT | *** |
Note: To avoid having to “H” route the customer reimbursement transaction for approval, it must be submitted prior to the repair transaction.
* To avoid warranty transaction rejections, the SPS Warranty Claim Code must be entered when submitting this transaction.
** Submit the dollar amount reimbursed to the customer in Net/Reimbursement. Submit $20.00 administrative allowance in Net/Admin Allowance.
*** Submit $10.00 administrative allowance in Net/Admin Allowance.
Warranty Claim Code Information Retrieval
If the SPS Warranty Claim Code was not recorded on the Job Card, the code can be retrieved in the SPS system as follows:
- Open TIS on the computer used to program the vehicle
- Select and start SPS
- Select Settings
- Select the Warranty Claim Code tab
The VIN, Warranty Claim Code and Date/Time will be listed on a roster of recent programming events. If the code is retrievable, dealers should resubmit the transaction making sure to include the code in the SPS Warranty Claim Code field.
Service Procedure
Note: Carefully read and follow the instructions below.
- Ensure the programming tool is equipped with the latest software and is securely connected to the data link connector. If there is an interruption during programming, programming failure or control module damage may occur.
- Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will interrupt programming. When required install the EL-49642 SPS Programming Support Tool to maintain system voltage. If not available, connect a fully charged 12 V jumper or booster pack disconnected from the AC voltage supply. DO NOT connect a battery charger.
- Turn OFF or disable systems that may put a load on the vehicles battery such as; interior lights, exterior lights (including daytime running lights), HVAC, radio, etc.
- Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/Maintenance (I/M) system status indicators to NO.
Note: If the Same Calibration/Software Warning is noted on the SPS controller screen, select “OK” and continue programming.
- Reprogram the engine control module. Refer to Engine Control Module: Programming and Setup in SI.
- Record SPS Warranty Claim Code on job card for warranty transaction submission.
- CALIFORNIA VEHICLES ONLY: Complete a “Proof of Correction” certificate and provide to the vehicle owner upon recall completion.
Note: If the DTC code (P0420) is stored, it is not a false store due to a software issue. The technician will need to perform SBD to address the P0420.
Dealer Responsibility
All new, used, GM Certified Used, courtesy transportation vehicles, dealer shuttle vehicles, etc. in dealers’ possession and subject to this program must be held and inspected/repaired per the service procedure of this bulletin before customers take possession of these vehicles. Involved vehicles must be held and not delivered to customers, dealer-traded, released to auction, used for demonstration, or any other purpose.
All GM Certified Used vehicles currently in the dealers’ inventory within the Certified Pre-Owned Inventory System (CPOIS) will be de-certified and must be held and remedied per the service procedure in this bulletin. Upon submitting an accepted/paid warranty transaction in the Global Warranty Management (GWM) system, the vehicle can be re-certified for sale within the CPOIS system, or once again be used in the CTP program.
Dealers are to service all vehicles subject to this program at no charge to customers, regardless of mileage, age of vehicle, or ownership, from this time forward.
Customers who have recently purchased vehicles sold from your vehicle inventory, and for which there is no customer information indicated on the dealer listing, are to be contacted by the dealer. Arrangements are to be made to make the required correction according to the instructions contained in this bulletin. A copy of the customer letter is provided in this bulletin for your use in contacting customers. Recall follow-up cards should not be used for this purpose, since the customer may not as yet have received the notification letter.
In summary, whenever a vehicle subject to this program enters your vehicle inventory, or is in your dealership for service in the future, you must take the steps necessary to be sure the program correction has been made before selling or releasing the vehicle.
When a California emissions recall is completed by a GM dealer, the dealer must provide the vehicle owner a “Proof of Correction Certificate” which the owner may need to present to the California Department Of Motor Vehicles (DMV) when renewing their vehicle registration. Without this correction certificate, the owner may be unable to renew their vehicle registration.
Additional Certificates can be obtained, at no charge, from the 1Store application in GlobalConnnect. Request GM Item Number 1825 when ordering.
Dealer Reports
For dealers with involved vehicles, a listing with involved vehicles has been prepared and will be provided to U.S. dealers through the GM GlobalConnect Recall Reports The listing may contain customer names and addresses obtained from Motor Vehicle Registration Records. The use of such motor vehicle registration data for any purpose other than follow-up necessary to complete this recall is a violation of law in several states/provinces/countries. Accordingly, you are urged to limit the use of this report to the follow-up necessary to complete this recall.
Customer Notification
General Motors will notify customers of this recall on their vehicle (see copy of customer letter included with this bulletin).
In order to ensure full protection under the emission warranty, and the right to participate in future recalls, the customer notification letter recommends that customers have their vehicles serviced as soon as possible. It also advises that failure to do so could legally be determined to be lack of proper maintenance. The vehicle may fail a state or local emission inspection test if the recall work is not completed.
Customer Reimbursement
Customer requests for reimbursement of previously paid repairs to correct the condition described in this bulletin are to be submitted to the dealer prior to or by May 31, 2018. See General Motors Service Policies and Procedures Manual, Section 6.1.11 – Product Field Action Customer Reimbursement Procedure.
May 2017
This notice applies to your vehicle, VIN:___________________________
Dear General Motors Customer:
This notice is sent to inform you that General Motors is conducting a voluntary emission recall that includes your vehicle.
Reason For This Recall: On certain 2013-2014 model year Chevrolet Cruze and Sonic vehicles equipped with a 1.8L engine, cracking of ceramic components internal to the catalytic converter may occur as a result of higher than anticipated exhaust temperatures. If this occurs the catalytic converter low efficiency diagnostic will set and the malfunction indicator lamp will illuminate.
What Will Be Done: Your GM dealer will reprogram the engine control module with calibrations that prevent higher than expected exhaust temperatures. This service will be performed for you at no charge.
How Long Will The Repair Take? Because of service scheduling requirements, it is likely that your dealer will need your vehicle longer than the actual service correction time of approximately 25 minutes.
What You Should Do: Please contact your GM dealer as soon as possible to arrange a service date. Instructions for making this correction have been sent to your dealer. Please ask your dealer if you wish to know how much time will be needed to schedule, process, and repair your vehicle.
If you have any questions or need any assistance, please contact your dealer or the appropriate Customer Assistance Center at the number listed below.
Division | Number | Text Telephones (TTY) |
Chevrolet | 1-800-630-2438 | 1-800-833-2438 |
Puerto Rico – English | 1-800-496-9992 | |
Puerto Rico – Español | 1-800-496-9993 | |
Virgin Islands | 1-800-496-9994 |
Reimbursement: Even though you may have already had repairs for this condition, you will still need to take your vehicle to your dealer for additional repairs. If you have paid for repairs for the condition described in this letter, please complete the enclosed reimbursement form and present it to your dealer with all required documents. Working with your dealer will expedite your request, however, if this is not convenient, you may mail the completed reimbursement form and all required documents to Reimbursement Department, PO Box 33170, Detroit, MI 48232-5170. The completed form and required documents must be presented to your dealer or received by the Reimbursement Department by May 31, 2018, unless state law specifies a longer reimbursement period.
Emission Law Information: In order to ensure your full protection under the emission warranty made applicable to your vehicle by state and federal law, and your right to participate in future recalls, it is recommended that you have your vehicle serviced as soon as possible. Failure to do so could legally be determined to be lack of proper maintenance of your vehicle. Also, your vehicle may fail a state or local emission inspection if this recall is not accomplished.
IMPORTANT MESSAGE FOR CALIFORNIA RESIDENTS
The California Air Resources Board (CARB) requires vehicle emission recalls be completed prior to California registration renewal. Uncorrected emission recalls will result in the inability to renew your California vehicle registration.
At the time of emission recall completion, your California dealer will issue a “Proof of Correction Certificate”. Keep this certificate and, if required, present it to the Department of Motor Vehicles when renewing your California registration as proof of recall completion.
We are sorry to cause you this inconvenience; however, we have taken this action in the interest of your continued satisfaction with our products.
Jeffrey M. Boyer
Vice President
Global Vehicle Safety
Enclosure
16186
16186-01
Release Date: June 2018
Revision: 01
https://www.nhtsa.gov/recalls?nhtsaId=10143749
https://static.nhtsa.gov/odi/tsbs/2018/MC-10143749-9999.pdf
To View or Download this Document Click Here
Reprogramming
GM Diagnostic/Programming (TIS2Web)
Approved J2534 Device with TIS2WEB can reprogram 1996 and later All GM Modules.
To obtain the latest electronic controller calibration information for your vehicle, go to https://tis2web.service.gm.com/tis2web and enter the vehicle's 17 character Vehicle Identification Number (VIN) and select 'Get CAL ID’.
You can then compare the latest part number with the actual number installed on the vehicle to determine if a reprogram is needed.
The Service Programming System (SPS) application is part of the TIS2Web system. To program an ECU, the SPS application must communicate with the vehicle control modules using the proper J2534 programming interface tool.
The following are the supported interface tools:
The Tech 2 supports model years 1996 and beyond. With the addition of the CAN Diagnostic Interface (CANdi) module, Tech 2 is fully backward compatible with current Tech 2 functionality and operates transparently when diagnosing non-CAN-equipped vehicles.
Servicing the next generation Global A vehicles will require the diagnostic software, GDS2, Global Diagnostic System 2 running on a local PC device while the MDI is connected to the vehicle. The GM MDI is the Global Diagnostic tool for future vehicles starting with Global A vehicles.
The GM MDI was introduced in the fall of 2007 for Pass-Thru programming and offers faster programming speed. It can be used to perform Pass-Thru programming on all vehicles built since 1996 and into the future. Click here to view a list of GDS supported vehicles.
- ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
- J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
- TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
- J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
- FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
- 【As a multi-protocol Pass-Thru vehicle interface】MaxiFlash Elite is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device. Specially designed to provide users with convenient PC communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, MaxiFlash Elite offers the most significant features desired by OEM customers: reliability, fast performance and flexibility.
- 【MaxiFlash Elite is an accessory tool for MK908P, MS908S Pro】Autel MaxiSys Elite to program ECUs on specific for BMW and for Benz vehicles, in case you lost the J-2534 programmer. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your tablet MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. The functions are NOT universally compatible. Please send VIN number to 🚘jmxd2022@outlook.com📧🚘 to check compatibility before your order. If need any supports, Please contact us.
- 【Wireless with advanced networking functions】Built-In Wireless with advanced networking functions and data storage. Fast performance ensures reprogramming even the newest controllers & Internet upgradable and updatable. Autel MaxiFlash Elite is compatiable with MaxiSYS MS908S, MaxiSYS MS908S Pro , MaxiSYS MS908CV, MaxiCOM MK908, MaxiCOM MK908 Pro, MaxiSYS Elite, MaxiSYS Elite II and Personal Computer
- 【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
- 【Supports simultaneous communication Definition in J2534-1】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed.Rugged aluminum case with non-slip rubber end caps, capable of withstanding harsh environment.
- 🔥【The King of Cost-Effectiveness From Autel】Fully upgraded from Autel MaxiSys EliteII /MS908S Pro/MK908P, Autel Scanner launched 2023 Newest 🅰🆄🆃🅴🅻 MaxiSys Elite II pro. 👉2 Years Free Update, ECU Programming&Coding, 38+ Service, Bidirectional Control, etc. Auto scanning 2.0 with all hardware parameters upgrade, provide total 8 (5+3)x diagnostic speed ✅CAN FD/ DOIP protocols support GM MY2020+ models, BMW E/F/G, Jaguar, Land Rover makes (Elite II can’t).
- 🔥【OE-LEVEL J2534 ECU PROGRAMMING & CODING】Enhance your diagnostics with the Elite II Pro J2534 Reprogramming scanner. This cutting-edge auto scanner supports : 1) program the new adaptive data to the on-board modules 2) replace the existing software/firmware in the ECUs 3) match the component control modules after repair or replacement 4) flash the hidden functions and 5) enhance the vehicle features. Experience 5X faster communication with SAE J2534-1 & -2 compliant programming interface.
- 🔥【38+ Maintenance Functions & High-End Functions】Autel scan tool Elite II Pro shares the same functional and deep service functions with other high-end scanners such as MaxiSys MS909/MS919/Ultra. 38+ special functions such as EPB/SAS/BMS/Oil/ABS/TPMS/Throttle/Injector/Suspension, etc., fix almost all “check engine” light issues. Bi-directional control, guided function, component matching, and scan VIN/license, together offer you effective and convenient diagnostic experiences.
- 🥇【DOIP& CAN FD Protocol, Top Hardware 5X Lightning Speed】Exclusive J2534 brings same DoIP & CAN FD protocol as Ultra/ MS919: CAN FD for GM MY2020+ Models; DOIP for BMW E/F/G Chassis, Jaguar, Land Rover makes. The improved hardware makes ELITE II PRO run more smoothly, even faster than MS919. It’s build with 8-Core CPU, Android 10.0 OS, 9.7’’ 1536*2048 touchscreen, 4GB&128GB, 11,000mAh battery, 2.4&5GHz dual-band WIFI, surpass Elite II/ Elite/ MS908S Pro II/ MK908 Pro II.
- 🔥【Free MV108 Assist Repairs】The MV108 digital inspection camera is designed to work with the MaxiSys series and PC, turning your MaxiSys scanner into a video inspection scope, allowing you to examine difficult-to-reach areas normally hidden from sight. It is capable of recording digital still images and videos, which offers you an economical solution to inspect machinery, facilities, and infrastructure quickly. One programmer tool Elite II Pro and one Videoscope MV108 make a perfect match.
- 🌐【Works with Autel MK908, MS908(S/Pro), MK908P, MaxiSys Elite】Autel J2534 work with these tools to program ECUs on specific BMW/ BENZ for specific functions. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your scanner MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, contact us via: 🚘auteldirect @ outlook. com🚘.
- 🌐【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
- 🌐【High-speed Transmission Speed】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed to save more times and win more business.
- 🌐【Multiple Devices Connected with PC】Autel MaxiFlash Elite J2534 also supports multiple device connections to the PC, which can operate diagnostic and reprogramming functions on more than one vehicle at the same time. Autel MaxiFlash Elite J2534 built-in wireless and data storage, which can update via Internet. It also ensures quickly reprogramming even the newest controllers.
- 🌐【Extensive Compatibility】Autel MaxiFlash J2534 is compatible with Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
- Industry-leading J2534 Pass-Thru Technology: Enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. Economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Each type (see single branded types above) Mongoose-Plus is engineered to work with one of the following OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, & VW/Audi.
- Supports Current & Earlier Vehicles: Enables diagnostics, programming and other “dealer” functions through OEM applications
- NEW Bluetooth Wireless Options Available: Providing wireless connectivity between your laptop and the Mongoose-Plus
- Expert Product Support: Staffed by technicians who understand vehicle repair and J2534 Pass‑Thru applications to help you with any technical setup questions
- Key Registration and Immobilizer Support: Using NASTF Vehicle Security Professional credentials
- Stay up-to-date with thelatest firmware and support of the SM2Pro J2534VCI ECUs programmer, ensuring reliable perform and optimalresults.
- The SM2Pro J2534VCI ECUs programmer is a trustedtool for professional technicians, offering comprehensive functionality and easy integration into your workflows.
- The SM2Pro J2534VCI ECUs programmer offersadvanced functionality for efficient and precise ECUs programming.
- With its 67IN1 without dongle & OBDcompatibility, the SM2Pro J2534VCI ECUs programmer provides a versatilesolution for read and write operations.
- Experienceseamless ECUs programming with the SM2Pro J2534VCI, designed to streamlines the read and write processes for enhanced efficiency.
Last update on 2024-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
Hello,
I’m the owner of a 2014 Chevy Equinox LT 2.4 L vehicle. I have experienced this same problem with my equinox. It currently has 87000 miles but the problem started around 78000 miles. The dealer will not cover for any of these cost. I need to know what can be done in my case. This is a fairly brand new vehicle in great condition. However, as this is a $1800 job, it is too much for us to pay and I frankly do not think it is fair for us to have to invest so much into a vehicle that has this many miles.
Thank you for your time,
Christian
You can make a complaint with NHTSA https://www-odi.nhtsa.dot.gov/VehicleComplaint/