“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10113609
Manufacturer Communication Number: PI1464
Summary
This preliminary informational bulletin provides diagnostic and repair information for a customer concern of a musty odor inside the driver/passenger compartment and/or water leak near the front dash of the vehicle.
Condition/Concern
Some customers may comment on a musty odor inside the driver/passenger compartment and/or water leak near the front dash of the vehicle. This most likely would have occurred after a heavy rain period or going through a car wash.
This may be caused by a void in the sealer that could allow water to pass from the body structure into the driver/passenger compartment area.
Recommendation/Instructions
If the above condition exists, follow the procedure below.
1. Perform normal waterleak test procedures. Refer to Waterleak Test Preparation in SI.
2. If the cause of the leak cannot be determined, remove the air inlet grille panel. Refer to Air Inlet Grille Panel Replacement in SI.
3. With the air inlet panel removed, visually inspect for voids in the body sealer on the affected side in areas illustrated above.
4. If there are voids found in the body sealer, apply high tech clear seam sealer, Kent Industries P/N P10200*, to the affected areas.
5. After all voids are filled, perform a waterleak test to verify the condition is corrected. Refer to Waterleak Test Preparation in SI.
Parts Information
Part Number | Description |
P10200 | HIGH – TECH CLEAR-SEAM SEALER |
2 Affected Products
Vehicle
MAKE | MODEL | YEAR |
CHEVROLET | MALIBU | 2014-2015 |
1 Associated Document
Manufacturer Communications
Bulletin No.: PI1464
Date: Apr-2015
https://www.nhtsa.gov/recalls?nhtsaId=10113609
- Plug Any Void –– Easily patch large cracks with confidence when using this thick auto seam sealer. This single-component panel bond compound provides superior adhesion on bare, primed, or painted metal surfaces on your vehicle or RV
- Complete Kit –– Comes with nitrile gloves and an application tip to make the process seamless This joint and seam filler set comes with everything you need and more. The sealant is compatible with any standard caulking gun
- Permanently Fill Gaps –– Don't settle for a body panel adhesive sealant that doesn't hold up. Trust in a non-shrinking, non-cracking and low odor formula that stays remarkably flexible over time. Prevent leaks and debris from infiltrating your vehicle, and promote corrosion resistance
- Primer and Paint Ready –– Get your project ready for the road in just 24 hours. Smooth out and let the quick-curing seam sealant settle in for 45 minutes. Then you're ready to prime and paint the automotive body filler for a flawless finish that blends right in
- All-Weather Performance –– High heat and humidity are no match for this car sealant. Enhanced moisture curing properties ensure a durable hold for interior or exterior use. Use a urethane sealer that is worlds ahead of any solvent-based solutions
- For professional use only – not for retail sale
- Fast curing and skins over quickly—can be painted 60 minutes after application
- Can be used for all sealing and adhesive applications with a standard caulking gun in both vertical and horizontal joints
- Flexible, non-staining, and non-sagging product that will not crack or shrink
- Plug Any Void –– Easily patch large cracks with confidence when using this thick auto seam sealer. This single-component panel bond compound provides superior adhesion on bare, primed, or painted metal surfaces on your vehicle or RV
- 2 Pack Value & Complete Kit - Comes with nitrile gloves and an application tip to make the process seamless This joint and seam filler set comes with everything you need and more. The sealant is compatible with any standard caulking gun
- Permanently Fill Gaps - Don't settle for a body panel adhesive sealant that doesn't hold up. Trust in a non-shrinking, non-cracking and low odor formula that stays remarkably flexible over time. Prevent leaks and debris from infiltrating your vehicle, and promote corrosion resistance
- Primer and Paint Ready - Get your project ready for the road in just 24 hours. Smooth out and let the quick-curing seam sealant settle in for 45 minutes. Then you're ready to prime and paint the automotive body filler for a flawless finish that blends right in
- All-Weather Performance - High heat and humidity are no match for this car sealant. Enhanced moisture curing properties ensure a durable hold for interior or exterior use. Use a urethane sealer that is worlds ahead of any solvent-based solutions
- SINGLE COMPONENT FORMULA: Adheres well to bare metal, primed metal and painted surfaces
- MOISTURE CURING PROPERTY: Provides excellent performance in high heat and humidity environments
- NON-SHRINKING, NON-CRACKING: Remains flexible and offers superior results to solvent-based sealers
- QUICK PAINTABILITY: Allows painting after 30-45 minutes
- THICK CONSISTENCY: Fills large voids and can be smoothed to a featheredge or brushed
- EASY APPLICATIONS: Brushable and paintable consistency
- HIGH ADHESION: Works on both bare metal and painted surfaces
- FAST SKINNING: Starts in about 10 to 15 minutes
- STAYS IN PLACE: Less likely to drip, sag or run out of gaps being sealed
- NON-STAINING: For all-purpose autobody joint and seam sealing
- Brushable Seam Sealer is fast drying and designed exclusively for automotive uses.
- This product remains flexible and will not crack, harden, sink or sag.
- Brushable Seam Sealer is easily applied with a brush and holds a perfect brush mark to match that O.E.M. seam.
- It provides excellent adhesion, seals cracks, crevices, body seams and is ideal for use on all lap and flange seams and joints.
- Brushable Seam Sealer is paintable in 30 to 60 minutes and comes in a light gray color.
- HIGH-PERFORMANCE: Two-part epoxy seals vertical and horizontal seams to match OEM seals
- METERED MIXING: Dual syringe cartridge eliminates the difficulty and mess of manual mixing
- NON-FLOWING: Heavy-bodied formula allows easy tooling for matching OEM seam sealer appearances
- QUICK CURE: Non-sag property aids during vertical applications
- SELF-MIXES: Makes a perfect formulation every time without mess
- Seal seams and permanently repair holes in tents, tarps, awnings, rainflys and camping gear like Thermarest sleeping pads
- Treat up to up to 12’ of seams (1 oz) or repair torn outdoor fabrics with an adhesive that cures into a flexible rubber seal; also available in an 8 oz tube
- Waterproof gear with a sealant that flexes with fabric and bonds to nylon, polyester, canvas, leather and vinyl
- Apply it to repair or re-proof gear without worrying about the seal peeling or cracking; includes two applicator brushes
- Packaging may vary
- Seal up to 60 ft of seams on tents, tarps and awnings with this water-based seam sealant; cures in 2 hours at room temperature
- Use it on various outdoor fabrics including nylon, polyester, and canvas; previously known as Seam Sure
- Apply this long-lasting seal that is nearly invisible and flexes with fabric; available in 2 fl oz bottle
- Treat gear using the included applicator brush to make application quick and easy
- Packaging may vary
- Vehicle Body Repair: Automotive Seam Sealer for all-purpose auto body gap filling,joint and seam sealing.Protect your vehicle from rust and corrosion with these automotive seam sealers.Ideal for car ,truck, boat, RVs.
- High Adhesive & Durable - designed this urethane sealer for a range of materials, including bare metal or painted surfaces.
- Don't Shrink and Crack - low odor single component formula auto seam sealer provides flexible,non-staining, and non-sagging.
- Easy to Use - Fast cure time.You can paint over the undercoating . For best results, allow 24 hours and scuff before painting.
- Water and Corrosion Proof - Use interior or exterior to prevent weather from eroding your car.Service Temperature -40 to 170 °F (-40 to 77 °C).High heat performance.
Last update on 2024-04-04 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
Bulletin No.: PI1464
Date: Apr-2015
Subject: Water Leak on Driver and/or Passenger Side Floor Models: 2014-2015 Chevrolet Malibu
Built at Fairfax (VIN Code F) and Prior to VIN Breakpoint FF262445 Attention: This PI also applies to any of the above models that may be Israel Export vehicles. Condition/Concern
Some customers may comment on a musty odor inside the driver/passenger compartment and/or water leak near the front dash of the vehicle. This most likely would have occurred after a heavy rain period or going through a car wash.
This may be caused by a void in the sealer that could allow water to pass from the body structure into the driver/passenger compartment area. Recommendation/Instructions
If the above condition exists, follow the procedure below.
1. Perform normal waterleak test procedures. Refer to Waterleak Test Preparation in SI.
2. If the cause of the leak cannot be determined, remove the air inlet grille panel. Refer to Air Inlet Grille Panel Replacement in SI.
3. With the air inlet panel removed, visually inspect for voids in the body sealer on the affected side in areas illustrated above.
4. If there are voids found in the body sealer, apply high tech clear seam sealer, Kent Industries P/N P10200*, to the affected areas.
5. After all voids are filled, perform a waterleak test to verify the condition is corrected. Refer to Waterleak Test Preparation in SI.
* We believe this source and their products to be reliable. There may be additional manufacturers of such products/materials. General Motors does not endorse, indicate any preference for, or assume any responsibility for the products or material from this firm or for any such items that may be available from other sources.
Parts Information
This product is currently available from Kent Industries (1-888-YES-KENT).
1 Part Number Description P10200* HIGH – TECH CLEAR-SEAM SEALER *There is enough material to perform multiple vehicles. Store the remaining material for future use. Warranty Information
For vehicles repaired under the Bumper-to-Bumper coverage (Canada Base Warranty coverage), use the following labor operation. Reference the Applicable Warranties section of Investigate Vehicle History (IVH) for coverage information. Labor Operation Description Labor Time 2080518* Apply Seam Sealer to Body Sealer Voids 1.1 hrs *This is a unique Labor Operation for Bulletin use only. It will not be published in the Labor Time Guide. GM bulletins are intended for use by professional technicians, NOT a “do-it-yourselfer”. They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information. WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION
2
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END
Driver floor wet when raining is there a recall of it only when it rain