Malfunction Indicator Lamp (MIL) Illuminated – DTC P0171 Set – 2011-2019 Buick Cadillac & Chevrolet

“This site contains affiliate links for which OEMDTC may be compensated”

NHTSA ID Number: 10161925

Manufacturer Communication Number: 19NA114

 

Summary

This informational bulletin provides information to the tech to test the PCV for proper performance before replacing the camshaft cover to correct a MIL On w/DTC P0171.

 

 


36 Affected Products

Vehicles

MAKE MODEL YEAR
BUICK ENCORE 2013-2019
CADILLAC ELR 2014-2017
CHEVROLET CRUZE 2011-2016
CHEVROLET SONIC 2012-2019
CHEVROLET TRAX 2013-2019
CHEVROLET VOLT 2012-2015

 


Condition

MIL is illuminated.

DTC P0171 (Fuel Trim System Lean) or other airflow related codes set in the Engine Control Module (ECM).

 

Cause

This condition may be caused by a torn positive crankcase ventilation (PCV) Crankcase Pressure Control Diaphragm.

⇒ The PCV crankcase pressure control diaphragm in the PCV valve could be torn, allowing un-metered air to enter the crankcase.

 

Information

Following the diagnostics in SI for that DTC may lead to the PCV system as a potential source of external airflow.

Confirmation of the PCV valve performance must be done before replacing the camshaft cover.

 


1 Associated Document

Manufacturer Communications

Bulletin No.: 19-NA-114
Date: May, 2019

https://www.nhtsa.gov/recalls?nhtsaId=10161925

MC-10161925-9999.pdf 85.283KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [83.28 KB]

 


NHTSA ID Number: 10161902

Manufacturer Communication Number: 19NA114

 

Summary

This informational bulletin provides information to the tech to test the PCV for proper performance before replacing the camshaft cover to correct a MIL On w/DTC P0171.

 

1 Associated Document

Manufacturer Communications

Bulletin No.: 19-NA-114
Date: May, 2019

https://www.nhtsa.gov/recalls?nhtsaId=10161902

MC-10161902-9999.pdf 85.283KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [83.28 KB]

 


NHTSA ID Number: 10149063

Manufacturer Communication Number: PIP5197J

 

Summary

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.

 

1 Associated Document

Manufacturer Communications

Bulletin No.: PIP5197J
Published date: 10/30/2018

https://www.nhtsa.gov/recalls?nhtsaId=10149063

MC-10149063-9999.pdf 2882.673KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [2.75 MB]

 


NHTSA ID Number: 10147383

Manufacturer Communication Number: PIP5197H

 

Summary

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.

 

1 Associated Document

Manufacturer Communications

Bulletin No.: PIP5197H
Published date: N/A

https://www.nhtsa.gov/recalls?nhtsaId=10147383

MC-10147383-9999.pdf 2882.651KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [2.75 MB]

 


NHTSA ID Number: 10137185

Manufacturer Communication Number: PIP5197G

 

Summary

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.

 

1 Associated Document

Manufacturer Communications

Bulletin No.: PIP5197G
Published date: 03/13/2018

https://www.nhtsa.gov/recalls?nhtsaId=10137185

MC-10137185-9999.pdf 75.968KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [74.19 KB]

 


NHTSA ID Number: 10113857

Manufacturer Communication Number: PIP5197E

 

Summary

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.

 

1 Associated Document

Manufacturer Communications

Bulletin No.: PIP5197E
Published date: 04/4/2017

https://www.nhtsa.gov/recalls?nhtsaId=10113857

MC-10113857-9999.pdf 548.906KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [536.04 KB]

 


NHTSA ID Number: 10114424

Manufacturer Communication Number: PIP5197B

 

Summary

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.

 

1 Associated Document

Manufacturer Communications

Bulletin No.: PIP5197B
Date: Feb-2015

https://www.nhtsa.gov/recalls?nhtsaId=10114424

MC-10114424-9999.pdf 1155.486KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [1.10 MB]

 


NHTSA ID Number: 10114390

Manufacturer Communication Number: PIP5197A

 

Summary

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.

 

1 Associated Document

Manufacturer Communications

Bulletin No.: PIP5197A
Date: Feb-2015

https://www.nhtsa.gov/recalls?nhtsaId=10114390

MC-10114390-9999.pdf 1155.973KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [1.10 MB]

 


NHTSA ID Number: 10112056

Manufacturer Communication Number: PIP5197

 

Summary

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.

 

1 Associated Document

Manufacturer Communications

Bulletin No.: PIP5197
Date: May-2014

https://www.nhtsa.gov/recalls?nhtsaId=10112056

MC-10112056-9999.pdf 1385.25KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [1.32 MB]

 


 

“This site contains affiliate links for which OEMDTC may be compensated”
SaleBestseller No. 1
Solary Automotive Smoke Machine Leak Detector - 12V DC EVAP Vacuum Diagnostic Tester for Pipe System
  • 【Multifunction】Our automotive smoke machine can perform various tests such as: EVAP system test, car sealing test, fuel tank system test, exhaust system test, intake system test and various pipe fittings test, ect. It Could be used on all cars, motorcycles, snowmobiles, ATV, light trucks, boats, etc.
  • 【Working Principle】 The automotive leak detector tool will change special oil(baby oil or mineral oil) into smoke, then blow smoke into sealed pipe system, you will find leak points in the pipe via the smoke. Please repair the part where leakage exists.
  • 【Easy to Use】The automotive smoke tester comes with a hook allows you to hang it on your hood latch. Just add 20ml of baby oil or mineral oil, then connect the detector with the DC12V battery, it can output thick smoke within 20s after turning on, thick smoke output detects even the smallest leaks.
  • 【Smart Protection】This smoke tester has overheat & freeze protection, the maximum temperature limit is 90°C, ture on antifreeze protection at a low temperature of -20°C. If it exceeds the working limit, such as over 90 ℃, it will automatically turn off the power to secure the safety of both the operator and device.
  • 【Lightweight and Portable】Most car smoke machine are bulky and heavy, which is not conducive to the transportation and storage of the equipment, and is only suitable for repair shops. Solary automotive smoke tester weighs only 3kg, to be small and light, not only for easy storage, but also for ease of use. It is an indispensable tool for all car owner.
Bestseller No. 2
Smoke Machine Automotive Leak Detector,Evap Vacuum Smoke Diagnostic Tester,Pipeline Fuel Leakage Detector Compatible with 12V Vehicles
  • 【Why Need It】For example: 1. The rupture of the vacuum hose will cause the mixture to be too thick, the idle speed will increase, the hot car will not start well, the engine will surge during acceleration, the fuel consumption will increase significantly, and the exhaust pipe will emit black smoke. 2. Blocking will cause the idle speed to drift, and the idle speed is easy to stall. 3. Air leakage in the vacuum tube will cause the engine to run weakly
  • 【No Air Pump】Connect shop air supply, connect 12V vehicle power, introduce shop air to the AUTOOL SDT103 fuel leak tester, turn the Flow Dial anti-clockwise to open the air flow, switch on the power at the back of the unit, then AUTOOL SDT103 smoke machine automotive will start to generate smoke.
  • 【External Flow Meter】You can easily control the air pressure, because the air pressure of each pipe in the car is different. If the air pressure is too high, the pipe will be damaged, and if the air pressure is too low, the leak will not be detected. Therefore, the flow meter is very important to protect your detection system more effectively. Make testing safer
  • EVAP Detection】American cars that began production in 1996 are equipped with EVAP service ports; in most American cars, the EVAP service port is usually located in the engine compartment, but the EVAP service port of some special models may be located in other locations. Open the plastic cover of the EVAP service port, then use the spool wrench to remove the check valve clockwise, then install the EVAP service port adapter, and introduce smoke from the port into the EVAP leak detection system.
  • 【Wide Testing Range】The smoke leak detector can do smoke testing of multiple systems, such as EVAP systems, Intake Systems, Cooling / EGR /Exhaust Systems, Crankcase Systems, Engine Airtightness, Vacuum Leaks, Low Pressure Turbo leaks.Applicable cars, motorcycles, snowmobiles, off-road vehicles, ATVs, light trucks and speedboats boats.
SaleBestseller No. 3
Automotive Smoke Machine - EVAP Leak Detector with Built-in Air Compressor, EVAP Service Port Adapter, OEM Approved Smoke Fluid - Model 01 – EVAP Vacuum Exhaust Smoke Detector Tools Kit
  • Automotive Smoke Machine for EVAP, Vacuum, Exhaust, and more leak testing diagnostics
  • Built in 1-PSI Air Compressor - All you'll need is to use your vehicle's 12V Battery. 1-PSI is the industrial standard for automotive leak testing and is safe for EVAP systems which must be tested under 1 PSI to prevent damage.
  • Approved Smoke Fluid - Included
  • Warranty - 3 Years Full Coverage
SaleBestseller No. 4
Automotive Smoke Machine Leak Tester for EVAP with Built-in Air Motor and Pressure Gauge – Model 03 - Exhaust Smoke Detector Tools Kit - Car Smoke Machine with Flow Meter and Smoke Fluid
  • Built in Air Pump - All you'll need is to use your vehicle's 12V Battery
  • Approved Smoke Fluid - Included.
  • Modes - Air mode to verify leaks even before introducing smoke. Smoke mode to introduce smoke into vehicle system for leak detection.
  • 2 Gauges - Pressure gauge to monitor total system pressure. Flow gauge to monitor leak size.
  • Adjustable Flow - With a precise knob for when you want slower, thicker smoke.
SaleBestseller No. 5
Solary Smoke Machine for Car - DC 12V EVAP Automotive Smoke Tester for Vacuum Leaks
  • [Automotive Smoke Machine SD302] Solary SD302 auto smoke machine is a professional machine for automotive pipe system leak detection, will help you find leaks and fix most general smoke leak problems. Supports various systems smoke testing, such as EVAP system, exhaust system, intake system, fuel tank system, engine airtightness, various pipe fittings and so on. Suitable for cars, motorcycles, trucks, off-road vehicles and speedboats boat, ect.
  • [Dual Mode] The smoke leak detector has air mode and smoke mode, two modes can be controlled independently. Air mode help you test whether there is a leak in the pipe by injecting air into the pipe, smoke mode help you lacate the leak accuarately. It can output thick smoke within 20s after turning on, thick smoke output detects even the smallest leaks.
  • [with Pressure Gauge] The smoke tester automotive has a pressure gauge, by observing the pressure gauge, you can determine whether the pipeline is leaking more quickly and accurately. Usually the pressure gauge value continues to rise, indicating that there is no problem with the pipeline. If the pressure gauge value continues to decrease, Explain that the pipeline leak needs to be repaired.
  • [Built-in Air Pump] Solary SD302 smoke machine leak detector has its own air pump and smoke generator, no need to buy additional air machines. We use high-quality materials, after many tests, the smoke created from the machine is non-toxic, don't worry about damage to your body and vehicle, please rest assured to use.
  • [ Overheating Protection] The car smoke machine has a smart protector to make it safe to use, if the system detects that the amount of e-liquid in the instrument is insufficient or the continuous working time is too long, the system is overheated, the overheat protection indicator ALARM light will light up, and the smoke will stop outputting until the temperature drops to the normal range, and the instrument will resume work, ensure operator and machine safety.
Bestseller No. 6
AutoLine Pro Ventus Automotive Smoke Machine with Built-in Li-Ion Battery, Air Compressor, Leak Size Flowmeter, OEM Approved Smoke Fluid, Cone Cap Plugs – EVAP Vacuum Exhaust Leak Detector Tools Kit
  • 【 The All New Ventus Smoke Machine Leak Detector 】 Experience The Future of Automotive Smoke Testing! Made for all Leak Testing Scenarios - EVAP, Vacuum, Intake, Exhaust, Turbo, Super Chargers, EGR, Cooling Systems Engine Blocks, Body Work, Oil Leaks, Trucks, Tractors, Scientific Apparatus, and more!
  • 【 World's #1 Li-ION BATTERY POWERED SMOKE MACHINE 】 Getting access to a vehicle battery takes time and lengthy power cables are messy. The Ventus completely eliminates this! Experience the insane level of portabilty by using the Fully Self Contained Ventus. It's the World's first Li-Ion Battery Powered Smoke Machine, rechargeable via USB-C.
  • 【 ZERO ODOR - 1 FLUID BOTTLE = 500+ TESTS 】 Ventus Atomic Smoke is so efficient that 1 bottle of fluid lasts 500+ tests! It also runs so clean that it's virtually odorless unlike other smoke machines in the market that smell terrible. Experience safe and clean smoke testing that will not linger and stink up your shop and clothes (If you know, you know!)
  • 【 BUILT-IN AIR COMPRESSOR MOTOR + LEAK SIZE GAUGE】 Create Clean and Ultra-Low Odor Smoke insatnatly! No air compressor needed. A Flow Meter backlit with LED light provides clear visibility for you to determine the Leak Size and Verify that leaks have been fixed.
  • 【 ALL NEW 2-in-1 Cone and Plugs Adapter System 】 Super Universal Adapter Kit made for injecting smoke into various sized openings and/or plugging them up too! Now INCLUDED with the VENTUS Smoke Machine.
Bestseller No. 7
ANCEL S3000 PRO Automotive Smoke Machine with Built-in Air Pump and Pressure Gauge. Professional Vehicle Leak Diagnostic Detector Tools Kit for Leaks Test in Vacuum,Fuel,EVAP and Other Cars System
  • 🕵【DETECT EVERY TYPE OF LEAK】Our versatile smoke machine for cars includes multiple vehicle cone adapters, a smoke delivery hose, intake bladder, and full-size automotive cap plugs. It seamlessly fits various lines and hoses, ideal for hassle-free checks on vacuum, fuel, engine, intake system and more
  • 🧰【USER-FRIENDLY AUTOMOTIVE SMOKE MACHINE】Begin your detection with just 4 simple steps using our automotive smoke tester. It's lightweight, portable, and even includes a built-in air pump for on-the-go jobs. Detect leaks effortlessly and elevate your automotive expertise. Don't miss out - revolutionize your auto experience and order this automotive tool today!
  • 🛡【VEHICLE-SAFE AUTOMOTIVE SMOKE TESTER】This smoke tester for vacuum leaks is made of thick solid metal, compact, and durable. It features an intelligent protector; if the operating temperature surpasses the limit, it will automatically power off to ensure the safety of both the operator and the smoke machine. This device uses baby oil to produce harmless smoke, perfect for all vehicle leak detection.
  • 💰【SAVE TIME AND MONEY WITH BUILT-IN AIR PUMP】Experience effortless leak detection with our car smoke machine's integrated air pump. No need for external air connections– making it easier to move around and test anywhere. Say goodbye to external air pump maintenance costs. Its all-in-one design ensures high effectiveness across various auto systems. Choose this convenient, cost savings, and versatile auto smoke machine leak detector.
  • 🚀【ACCURATE LEAK DETECTION and PRESSURE DECAY TEST】with built-in adjustable flow meter and pressure gauge, our smoke tester for vacuum leaks can quickly and accurately detect even the smallest leaks, ensuring precise diagnoses every time. It also supports pressure decay test, identifying tiny leaks by applying specific pressure and monitoring the gauge, especially useful for hard-to-spot leaks.
SaleBestseller No. 8
PowerScale M1 Automotive Smoke Machine Built-in Air Pump, 19-23 PSI Leak Detection, 2024 Professional Tools, EVAP System, Fuel Leakage, Leakage Diagnostic Tester for All DC12V Vehicles
  • 🛒【Opportunity】Grab your Powerscale M1 Smoke Machine Leak Detector now! Seize this opportunity to get more for your money, including lifelong technical support, a comprehensive 3-year warranty, and a hassle-free 30-day return and exchange policy. Our customer service team is ready to assist you 24/7, ensuring a smooth experience.Whether it's about model details, features, user guides, or after-sales care. Shop with confidence and enjoy peace of mind with every purchase!
  • 🧰【Comprehensive Leak Detection】The Powerscale M1 Automotive Smoke Machine can easily inspect various vehicles, including older models, for leaks in throttle shafts, engine blocks, turbo test systems, crankcase systems, intake systems, exhaust systems, fuel tank systems, EVAP systems, EGR systems, cooling systems, and various pipe fittings.
  • 🎉【High Performance and Premium Build】The Powerscale M1 does not require an external air source, equipped with a built-in air pump. Its compressor can generate air pressure from 19 to 23 psi, allowing smoke to be easily introduced into the system being tested, speeding up the leak detection process.
  • 🍃【Safe for Your Vehicle】Powerscale M1 heats baby oil or mineral oil to produce non-toxic smoke, ensuring no harm to the human body. It features a smart protector that automatically powers off in extreme temperatures to ensure the safety of both the operator and the equipment.
  • 🧩【User-Friendly Operation】 Designed with ease of use in mind, the Powerscale smoke machine features a straightforward interface, making it accessible for both professional mechanics and beginners. It stands out among fuel leak detectors, offering a seamless experience akin to high-end models like the Powerscale M3 smoke machine.
SaleBestseller No. 9
AutoLine Pro Automotive Smoke Machine Leak Detector EVAP Vacuum Diagnostics Tester | Economy Series
  • 【 HIGH PERFORMANCE】Made in the USA. The Economy Series version 2.0 outputs lots of smoke! It's compact, powerful, and all quality components have been UPGRADED+ in version 2.0. All units come with our brand new ALP HIGH YIELD Ceramic Smoke System guaranteed to produce more smoke than all competition and last forever (smoke coil has our lifetime warranty).
  • 【 DIAGNOSE ALL TYPES OF LEAKS】Consistently smoke test EVAP / Vacuum / exhaust / and more at a fraction of the cost.
  • 【 PRECISE AND SAFE】Engineered 100% safe for all vehicles. Thick Smoke output detects even the smallest leaks. Every unit Is backed by 1 YEAR FULL COVERAGE WARRANTY! AS AN AMERICAN FAMILY BUSINESS, we stand proudly behind our products. If you have any issues, don't hesitate to contact us directly.
  • 【 HOW DOES IT WORK?】(1) Fill with the included OEM Approved Smoke Fluid. The kit operates with the included OEM Approved Fluid or you may use your own USP Mineral Oil / Baby Oil. (2) Fasten the Power Cable (3) Connect your Air Supply. ANY SIZE and ANY TYPE OF AIR COMPRESSOR WILL WORK. (4) Check for LEAKS with Smoke Detection Technology.
Bestseller No. 10
FOXWELL ST201 Smoke Machine Automotive Built-in Air Compressor, EVAP Vacuum Exhaust Engine System Pipe Diagnostic Tester, High Pressure Smoke Leak Detector for All DC12V Vehicles
  • [Huge Surprise!] 🎁Enter the code 'Y3VWU2VI' to receive additional gifts - a tool case that can stash clips, EVAP service gear, power cords, and more accessories. Keep your workbench tidy and make it easier to take on the go.
  • [Flexible 2-in-1 Design] Offering exceptional flexibility and portability. Free from the need for external cumbersome air pumps, this smoke machine automotive allows you to work effortlessly in garages, yards, parking lots, or outdoor work areas. No need to be restricted by location, you can test anywhere.
  • [Scientific Pressure Output] Operating within a 0.8-1.2 bar output pressure range, accurately simulating real-time vehicle conditions. The Foxwell ST201 car smoke machine perfectly match with intake, exhaust, and vacuum systems, etc., Reduceing the risk of system damage or unreliable results due to excessively high or low pressure.
  • [Exclusive Operating Technology] Adopting the only variable frequency operation technology on the market, ensuring controlled temperatures for enhanced safety and prolonged smoke tester lifespan. With a 10-minute work cycle, restart effortlessly with a single button for continued testing without interruptions.
  • [Hassle-Free Service] P-urchase the ST201 smoke leak detector automotive with confidence! Benefit from 24/7 customer service, product warranties, and expert technical guidance. We're committed to your satisfaction, ensuring the best user experience. Buy now for worry-free automotive diagnostics!

Last update on 2024-03-07 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

 


2 thoughts on “Malfunction Indicator Lamp (MIL) Illuminated – DTC P0171 Set – 2011-2019 Buick Cadillac & Chevrolet”

  1. Is there a similar problem on 2012 sonics with the 1.4l? The PCV valve is leaking and the non-return valve is not visible upon inspection. Can these repair procedures be applied to my sonic?

    Reply

Leave a Reply to Daniel Sandoval Cancel reply

Share to...